NEC MT1075/MT1065 user manual Battery Installation, Remote Control Precautions

Page 11

Battery Installation

1. Press firmly and slide the battery cover off.

2.Remove both old batteries and install new ones (AA). Ensure that you have the batteries' polarity (+/-) aligned correctly.

3.Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries.

Remote Control Precautions

•Handle the remote control carefully.

•If the remote control gets wet, wipe it dry immediately.

•Avoid excessive heat and humidity.

•If you will not be using the remote control for a long time, remove the batteries.

•Do not place the batteries upside down.

•Do not use new and old batteries together, or use different types of batteries together

Operating Range for Wireless Remote Control

Remote sensor on the projector cabinet

7m/22 feet

7m/22 feet

Remote control

Remote sensor on the projector cabinet

Note on Remote Control Operation:

If you press and hold the SELECT button while installing new batteries, the remote control may fail to work properly.

Should this happen, remove the batteries and then install them again without touching the SELECT button.

•The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.

•The projector will not respond if there are objects between the re- mote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE mini jack and the other end to the remote jack on the remote control.

REMOTE

E-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents MT1075/MT1065 Safety Cautions For North America only MT1065 only Fire and Shock PrecautionsLamp Replacement Whats in the Box?Table of Contents Introduction to the Projector Features youll enjoyIntroduction Carrying the Projector Part Names of the ProjectorAttaching the lens cap Select Top FeaturesTerminal Panel Features On the screen using the Select Part Names of the Remote ControlSelect Using the Remote Control in Wired Operation Battery InstallationRemote Control Precautions Operating Range for Wireless Remote ControlSelecting a Location Installation and ConnectionsSetting Up the Screen and the Projector Reflecting the Image Distance ChartDo not attempt to install the projector yourself Throw Distance and Screen SizeConnecting Your PC with a DVI Connector When Viewing a DVI Digital SignalConnecting Your PC or Macintosh Computer Connecting to RGB 2 in connectorsTo connect Scart output RGB Connecting an External MonitorDVD player Connecting Your DVD PlayerConnecting the Supplied Power Cable Connecting Your VCR or Laser Disc PlayerTurning on the Projector Projecting AN Image Basic OperationSelecting a Source Adjusting the Picture Size and PositionUsing the Remote Control Adjust the Tilt FootUse the Focus Button +/- to obtain the best focus When using the remote control or cabinet buttonsUsing Auto Focus FocusConfirmation screen is displayed When using the USB connected to the projectorOptimizing RGB Picture Automatically Turning Up or Down VolumeUsing the Laser Pointer Adjusting the Image Using Auto AdjustTo turn off the projector Setting the function switchTurning off the Projector Using the Remote Mouse Function Convenient FeaturesAuto 3D Reform Executing the Auto 3D Reform featureAdjustment Setting Screen of Auto 3D ReformGetting the On-line Help Using the PointerFreezing a Picture Using the middle button on the mouse Using a USB Mouse Using the USB HUB FunctionOperate the Menus using the USB mouse USB Memory Device or USB Memory Card Reader Support Changing Background LogoMaking Freehand Drawings on a Projected Image ChalkBoard Making the Most out of the Viewer Function Using the ViewerProjecting slides Viewer When the tool bar is not displayedOperating the Viewer Function from the Projector playback Preparations Auto Play ModeSwitching to Slides Directly from Other Input Modes Viewing Digital ImagesTo delete captured images Using the PC Card Files Fucntion PC Card FilesDeleting Captured Images Basic Menu Operation Using ON-SCREEN MenuUsing the Menus Default Custom Menu items areAdvanced Menu Menu treeCommunication Speed Operation Mode SelectDefault Source Select WEP Menu Elements Source Select Entering Alphanumeric Characters by Using the MenuMenu Descriptions & Functions Image Options Entry Edit CommandPicture not available for Viewer and LAN SoundPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Button to move the yellow box to select a Menu Setup Resolution manually User can adjust the image display functions HoriSelecting Lamp Mode and Lamp Type Lamp Setting Selecting Auto Functions Selecting Aspect Ratio and Position for Screen ScreenNetwork Type required for wireless only Setting LAN ModePared to use of 64bit datalength encryption WEP for Wireless onlyNications may be monitored by someone Uses 64-bit datalength for secure transmissionDelete Setting a PasswordStatus EntryTo delete PC card data you registered To enable Security, use the SelectSecurity Help Returning to Factory DefaultTools To replace the lamp MaintenanceReplacing the Lamp Vacuum the filter-through the filter cover CleaningCleaning or Replacing the Filter Cleaning the Cabinet and the LensLamp Indicator TroubleshootingPower Indicator Status IndicatorFor more information contact your dealer Common Problems & Solutions Check These ItemsImage isn’t square to Page Model Number MT1075 Optical SpecificationsModel Number MT1065 Optical Pin No RGB Signal Analog YCbCr Signal Cabinet DimensionsPin Assignments of D-Sub RGB Input Connector Mini D-Sub 15 Pin ConnectorCompatible Input Signal List Cable Connection PC Control Connector D-SUB 9PUsing Software Keyboard PC Control Codes and Cable ConnectionHandling of the Address for Operation via a Browser Operation Using an Http BrowserOverview Preparation Before UseTravelCare Guide TravelCare a service for international travelersServices offered with TravelCare Term of warrantyKuala Lumpur, Malaysia Asia and Middle EastApplication Sheet for TravelCare Service Program Condition of your TravelCare Service Program

MT1075/MT1065 specifications

The NEC MT1075 and MT1065 are high-quality projectors that cater to various presentation needs, making them popular choices in both business and educational settings. Known for their impressive specifications and features, these models deliver outstanding performance, complemented by advanced technologies.

One of the standout features of the NEC MT1075 and MT1065 is their brightness. The MT1075 boasts a luminous output of 3700 ANSI lumens, while the MT1065 offers a slightly lower output of 3600 ANSI lumens. This high brightness level ensures that images remain clear and vivid, even in well-lit environments, making them suitable for large auditoriums, classrooms, and conference rooms.

These projectors employ DLP (Digital Light Processing) technology, which enhances image quality by providing sharp, vibrant colors and high contrast ratios. DLP technology ensures that moving images appear smooth and free from motion blur, making these projectors ideal for displaying videos, animations, and dynamic presentations. The MT1075 and MT1065 also support various resolution formats, with their native SVGA (800 x 600) resolution able to accommodate higher resolutions with clarity.

Another significant characteristic of these projectors is their connectivity options. Both models offer a range of input ports, including VGA, composite video, and S-Video, ensuring compatibility with multiple devices such as laptops, DVD players, and gaming consoles. Additionally, they feature audio input and built-in speakers, providing a complete multimedia experience.

The lightweight design of the NEC MT1075 and MT1065 enhances portability, making them easy to transport and set up in different locations. Their built-in features, such as keystone correction and manual zoom, provide flexibility in positioning the projectors and adjusting the image to fit various screen sizes.

Energy efficiency is another important aspect of the NEC MT1075 and MT1065. Both models utilize advanced lamp technology that ensures long-lasting performance, reducing the frequency of lamp replacements and associated maintenance costs.

Overall, the NEC MT1075 and MT1065 projectors are versatile and reliable, making them suitable for a wide range of applications. Their combination of brightness, advanced DLP technology, connectivity options, and user-friendly features make them an excellent choice for professionals and educators looking to make impactful presentations. With their durability and enhanced image quality, the MT1075 and MT1065 stand out in the competitive projector market.
Top Page Image Contents