NEC MT1075/MT1065 user manual Selecting Lamp Mode and Lamp Type Lamp Setting

Page 48

[Page 5]

Remote Sensor:

This option determines which remote sensors on the projector are enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes indicate that they can accept the infrared signal from the supplied remote control.

S-Video Mode Select:

This feature is used to select the S-Video signal detection mode. This allows identifying of the S-Video signals with different aspect ratio (16:9 and 4:3).

Off

Does not identify any S-video signal.

S2

Identifies the 16:9 or 4:3 signal.

[Page 6]

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (D-Sub 9 Pin). It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs).

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each time the projector is turned on.

Last

Sets the projector to default to the previous or last

 

active input each time the projector is turned on.

Auto

Searches for an active source in order of RGB1 →

 

RGB2 → Video → S-Video → DVI(DIGITAL) → Viewer

 

→ RGB1 and displays the first found source.

Select

Displays the selected source input every time the pro-

 

jector is started up. Select an input from the pull-down

 

menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

*This Control Panel Key Lock does not affect the remote control and the PC Control functions.

*When the cabinet buttons are disabled, pressing and holding the CANCEL button for about 10 seconds will change the setting to enabled.

Selecting Lamp Mode and Lamp Type [Lamp Setting]

Lamp Mode:

This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be extended by using the Eco mode.

Normal Mode . This is the default setting (100% Brightness).

Eco Mode

Select this mode to increase the lamp life (80% Bright-

 

ness).

Lamp Type:

The lamp type you use is displayed here.

MT70LP

Standard life lamp (MT1075)

MT60LP

Standard life lamp (MT1065)

MT60LPS

Optional extended life lamp. When the optional ex-

 

tended life lamp is used, the Lamp Mode is available.

E-48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents MT1075/MT1065 Safety Cautions Fire and Shock Precautions Lamp ReplacementWhats in the Box? For North America only MT1065 onlyTable of Contents Features youll enjoy IntroductionIntroduction to the Projector Part Names of the Projector Attaching the lens capCarrying the Projector Top Features SelectTerminal Panel Features Part Names of the Remote Control On the screen using the SelectSelect Battery Installation Remote Control PrecautionsOperating Range for Wireless Remote Control Using the Remote Control in Wired OperationInstallation and Connections Setting Up the Screen and the ProjectorSelecting a Location Distance Chart Do not attempt to install the projector yourselfThrow Distance and Screen Size Reflecting the ImageWhen Viewing a DVI Digital Signal Connecting Your PC or Macintosh ComputerConnecting to RGB 2 in connectors Connecting Your PC with a DVI ConnectorConnecting an External Monitor To connect Scart output RGBConnecting Your DVD Player DVD playerConnecting Your VCR or Laser Disc Player Connecting the Supplied Power CableProjecting AN Image Basic Operation Turning on the ProjectorAdjusting the Picture Size and Position Using the Remote ControlAdjust the Tilt Foot Selecting a SourceWhen using the remote control or cabinet buttons Using Auto FocusFocus Use the Focus Button +/- to obtain the best focusWhen using the USB connected to the projector Confirmation screen is displayedTurning Up or Down Volume Using the Laser PointerAdjusting the Image Using Auto Adjust Optimizing RGB Picture AutomaticallySetting the function switch Turning off the ProjectorTo turn off the projector Convenient Features Using the Remote Mouse FunctionExecuting the Auto 3D Reform feature Auto 3D ReformSetting Screen of Auto 3D Reform AdjustmentUsing the Pointer Freezing a PictureGetting the On-line Help Using a USB Mouse Using the USB HUB Function Operate the Menus using the USB mouseUsing the middle button on the mouse Changing Background Logo Making Freehand Drawings on a Projected Image ChalkBoardUSB Memory Device or USB Memory Card Reader Support Using the Viewer Making the Most out of the Viewer FunctionWhen the tool bar is not displayed Operating the Viewer Function from the Projector playbackProjecting slides Viewer Auto Play Mode Switching to Slides Directly from Other Input ModesViewing Digital Images PreparationsUsing the PC Card Files Fucntion PC Card Files Deleting Captured ImagesTo delete captured images Using ON-SCREEN Menu Using the MenusDefault Custom Menu items are Basic Menu OperationMenu tree Advanced MenuOperation Mode Select Default Source SelectCommunication Speed WEP Menu Elements Entering Alphanumeric Characters by Using the Menu Menu Descriptions & FunctionsSource Select Entry Edit Command Picture not available for Viewer and LANSound Image OptionsPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Button to move the yellow box to select a Menu Setup User can adjust the image display functions Hori Resolution manuallySelecting Lamp Mode and Lamp Type Lamp Setting Selecting Aspect Ratio and Position for Screen Screen Selecting Auto FunctionsSetting LAN Mode Network Type required for wireless onlyWEP for Wireless only Nications may be monitored by someoneUses 64-bit datalength for secure transmission Pared to use of 64bit datalength encryptionSetting a Password StatusEntry DeleteTo enable Security, use the Select SecurityTo delete PC card data you registered Returning to Factory Default ToolsHelp Maintenance Replacing the LampTo replace the lamp Cleaning Cleaning or Replacing the FilterCleaning the Cabinet and the Lens Vacuum the filter-through the filter coverTroubleshooting Power IndicatorStatus Indicator Lamp IndicatorCommon Problems & Solutions Check These Items Image isn’t square toFor more information contact your dealer Page Specifications Model Number MT1075 OpticalModel Number MT1065 Optical Cabinet Dimensions Pin Assignments of D-Sub RGB Input ConnectorMini D-Sub 15 Pin Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List PC Control Connector D-SUB 9P Using Software KeyboardPC Control Codes and Cable Connection Cable ConnectionOperation Using an Http Browser OverviewPreparation Before Use Handling of the Address for Operation via a BrowserTravelCare a service for international travelers Services offered with TravelCareTerm of warranty TravelCare GuideAsia and Middle East Kuala Lumpur, MalaysiaApplication Sheet for TravelCare Service Program Condition of your TravelCare Service Program

MT1075/MT1065 specifications

The NEC MT1075 and MT1065 are high-quality projectors that cater to various presentation needs, making them popular choices in both business and educational settings. Known for their impressive specifications and features, these models deliver outstanding performance, complemented by advanced technologies.

One of the standout features of the NEC MT1075 and MT1065 is their brightness. The MT1075 boasts a luminous output of 3700 ANSI lumens, while the MT1065 offers a slightly lower output of 3600 ANSI lumens. This high brightness level ensures that images remain clear and vivid, even in well-lit environments, making them suitable for large auditoriums, classrooms, and conference rooms.

These projectors employ DLP (Digital Light Processing) technology, which enhances image quality by providing sharp, vibrant colors and high contrast ratios. DLP technology ensures that moving images appear smooth and free from motion blur, making these projectors ideal for displaying videos, animations, and dynamic presentations. The MT1075 and MT1065 also support various resolution formats, with their native SVGA (800 x 600) resolution able to accommodate higher resolutions with clarity.

Another significant characteristic of these projectors is their connectivity options. Both models offer a range of input ports, including VGA, composite video, and S-Video, ensuring compatibility with multiple devices such as laptops, DVD players, and gaming consoles. Additionally, they feature audio input and built-in speakers, providing a complete multimedia experience.

The lightweight design of the NEC MT1075 and MT1065 enhances portability, making them easy to transport and set up in different locations. Their built-in features, such as keystone correction and manual zoom, provide flexibility in positioning the projectors and adjusting the image to fit various screen sizes.

Energy efficiency is another important aspect of the NEC MT1075 and MT1065. Both models utilize advanced lamp technology that ensures long-lasting performance, reducing the frequency of lamp replacements and associated maintenance costs.

Overall, the NEC MT1075 and MT1065 projectors are versatile and reliable, making them suitable for a wide range of applications. Their combination of brightness, advanced DLP technology, connectivity options, and user-friendly features make them an excellent choice for professionals and educators looking to make impactful presentations. With their durability and enhanced image quality, the MT1075 and MT1065 stand out in the competitive projector market.
Top Page Image Contents