Epson ELP-3300 owner manual Safety Instructions

Page 15

Safety Instructions

Follow these safety instructions when setting up and using the projector:

1.Do not place the projector on an unstable cart, stand, or table.

2.Do not use the projector near water or sources of heat.

3.Use attachments only as recommended.

4.Use the type of power source indicated on the projector. If you are not sure of the type of power available, consult your dealer or local power company.

5.Insert the projector’s three-wire grounding-type plug into a properly grounded outlet. If you have a two-prong outlet, contact an electrician to replace it.

6.Do not overload wall outlets, extension cords, or integral convenience receptacles. This can cause fire or electric shock.

7.Do not place the projector where the cord can be walked on.

8.Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.

9.Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not put the projector on a sofa, rug, or other soft surface or in a built-in installation unless proper ventilation is provided.

xivIntroduction

Image 15

Contents Epson Page Iii Important Safety Information Remote Control Information Important Information About Your ELP-3300Ambient light is too bright Readme File Information Contents Using the Projector Remote Control of the Computer Troubleshooting Introduction Getting the Most Out of Your Projector Serial Communication Kit Optional Accessories About This Manual Safety Instructions Safety Instructions 800 Where to Get HelpEpson Download Service Electronic support servicesEnergy Star Compliance 614 529-1611or your local CompuServe access numberInstallation Unpacking the Projector Additional components Maximum Zoom Setting Up the ProjectorSetting Up the Projector Connecting to a Computer Connecting to a PC desktop computer Connecting to a PC laptop computer Connecting to a desktop Macintosh Connecting to a PowerBook Connecting to a Video Source Yellow Video/audio cable Connecting to an Audio Source You should now adjust the Fade menu setting. See Connecting to an External Speaker or PA SystemConnecting the serial cable Setting Up Serial CommunicationModem port is identified by the following icon Installing the softwareConnecting the Remote Control with the Lead Wire Installation Using the Projector Turning the Equipment On and Off Focusing and Positioning the Screen Image Using the Projector Controlling the Projector Controlling the ProjectorStandby Sync + Button/component Function You see a screen similar to the following Adjusting the settings from ELP LinkMonitoring the Projector Using Rear Projection Using the Menus Following table shows the settings for each of the menus Accessing the MenusTo close the menus, again press the Menu button Changing menu settingsAccessing ELP Link menus Restoring the default settings Menu SettingsComputer menu Tracking Lines until they disappearScreen wider than the projector’s area Video menu Display menu Projection, Rear Proj should be off Blank ToBlue. For a description of Blank, see Rear ProjAudio menu Options menu Custom menu LanguageJapanese Using the Menus Remote Control of the Computer Windows Macintosh ELP Remote Programmer TemplatesDo the following to start the ELP Remote Programmer Starting the ELP Remote ProgrammerRemote Control of the Computer Element Function Assigning a Macro to a Programmable Button Assigning a Macro to a Programmable Button Using record modeRemote Control of the Computer Activating a Template Using manual modeELP Remote Programmer Menus Maintenance Cleaning the Lens Cleaning the Projector CaseCleaning the Air Filter Cleaning the Air Filter Cleaning the Trackball Cleaning the Trackball Replacing the Lamp When the screws are loose, lift off the lamp cover Turn the projector over so you can access the lamp coverLift up the handle and pull out the lamp Resetting the lamp timer Replacing the Fuse Replacing the Fuse Maintenance Troubleshooting Status light Color Problems with the ProjectorPower status light does not come on For specific problems, see the followingTemperature status light is orange An image does not appear on the screen Problems with the Image or SoundOnly the test pattern is displayed Colors of the image are not right Problems with the Remote Control Using the trackball has no effect Troubleshooting General Technical SpecificationsOptical Electrical Supported Monitor Displays Pin Assignments Monitor and VGA connector pin assignments Brightness. The balance of light and dark shades in an image Glossary82Glossary Glossary83 84Glossary Index 86Index Index87 88Index Index89 66-68 Tint