Epson ELP-3300 owner manual Problems with the Projector, Status light Color

Page 85

Problems with the Projector

If you are having problems with the projector, first check the status lights at the top of the projector. These lights monitor the operation of the projector.

 

temperature light

power light

 

lamp light

 

 

 

Status light

Color

Status

 

 

 

Temperature

Flashing orange

The projector is hot.

 

Orange

The projector is too hot.The lamp turns off.

Lamp

Flashing green

The lamp is warming up.

 

Green

The lamp is on.

 

Flashing orange

The lamp is cooling down.

 

Flashing green

The lamp has been used for 700 hours and

 

and orange

should be replaced.

 

Flashing red

The lamp is not working.

Power

Orange

The projector is in standby mode.

 

Green

The projector and lamp are on.

 

Flashing green

The projector is receiving a signal from the

 

 

remote control.

 

Flashing red

There is a problem with the projector.

 

 

 

66

6 • Troubleshooting

Image 85
Contents Epson Page Iii Important Information About Your ELP-3300 Important Safety Information Remote Control InformationAmbient light is too bright Readme File Information Contents Using the Projector Remote Control of the Computer Troubleshooting Introduction Getting the Most Out of Your Projector Serial Communication Kit Optional Accessories About This Manual Safety Instructions Safety Instructions 800 Where to Get HelpEpson Download Service Electronic support servicesEnergy Star Compliance 614 529-1611or your local CompuServe access numberInstallation Unpacking the Projector Additional components Maximum Zoom Setting Up the ProjectorSetting Up the Projector Connecting to a Computer Connecting to a PC desktop computer Connecting to a PC laptop computer Connecting to a desktop Macintosh Connecting to a PowerBook Connecting to a Video Source Yellow Video/audio cable Connecting to an Audio Source You should now adjust the Fade menu setting. See Connecting to an External Speaker or PA SystemConnecting the serial cable Setting Up Serial CommunicationModem port is identified by the following icon Installing the softwareConnecting the Remote Control with the Lead Wire Installation Using the Projector Turning the Equipment On and Off Focusing and Positioning the Screen Image Using the Projector Controlling the Projector Controlling the ProjectorStandby Sync + Button/component Function You see a screen similar to the following Adjusting the settings from ELP LinkMonitoring the Projector Using Rear Projection Using the Menus Following table shows the settings for each of the menus Accessing the MenusTo close the menus, again press the Menu button Changing menu settingsAccessing ELP Link menus Restoring the default settings Menu SettingsComputer menu Lines until they disappear TrackingScreen wider than the projector’s area Video menu Display menu Blue. For a description of Blank, see Blank ToRear Proj Projection, Rear Proj should be offAudio menu Options menu Language Custom menuJapanese Using the Menus Remote Control of the Computer Windows Macintosh ELP Remote Programmer TemplatesDo the following to start the ELP Remote Programmer Starting the ELP Remote ProgrammerRemote Control of the Computer Element Function Assigning a Macro to a Programmable Button Assigning a Macro to a Programmable Button Using record modeRemote Control of the Computer Activating a Template Using manual modeELP Remote Programmer Menus Maintenance Cleaning the Projector Case Cleaning the LensCleaning the Air Filter Cleaning the Air Filter Cleaning the Trackball Cleaning the Trackball Replacing the Lamp When the screws are loose, lift off the lamp cover Turn the projector over so you can access the lamp coverLift up the handle and pull out the lamp Resetting the lamp timer Replacing the Fuse Replacing the Fuse Maintenance Troubleshooting Status light Color Problems with the ProjectorPower status light does not come on For specific problems, see the followingTemperature status light is orange An image does not appear on the screen Problems with the Image or SoundOnly the test pattern is displayed Colors of the image are not right Problems with the Remote Control Using the trackball has no effect Troubleshooting General Technical SpecificationsOptical Electrical Supported Monitor Displays Pin Assignments Monitor and VGA connector pin assignments Brightness. The balance of light and dark shades in an image Glossary82Glossary Glossary83 84Glossary Index 86Index Index87 88Index Index89 66-68 Tint