Epson ELP-3300 owner manual Starting the ELP Remote Programmer

Page 64

Starting the ELP Remote Programmer

The ELP Remote Programmer can run under Windows or on the Macintosh. This section provides general information that applies to both platforms. For specific information on how to use the ELP Remote Programmer on your platform, see the online help, which is available by selecting Help in the menu bar.

Do the following to start the ELP Remote Programmer:

•Windows: Open the ELP Utility program group by double-clicking on it. Then double-click the ELP Remote Programmer icon.

•Macintosh: Open the ELP Utilities folder by double-clicking on its icon. Double-click the ELP Remote Programmer folder and then double-click the ELP Remote Programmer icon.

When you start the ELP Remote Programmer, you see a screen similar to the one on the next page. This screen, which represents the buttons on the remote control, allows you to change the button assignment and then activate the template so you can use it with the remote control.

The ELP Remote Programmer must be running on your computer in order for you to use the remote control to control your software program. If you do not need to program any buttons, you can minimize the ELP Remote Programmer screen so it appears as an icon at the bottom of the screen.

Note: Although both ELP Remote Programmer and ELP Link can be running on your computer at the same time, only one can be active. If both are running, ELP Link has priority.

Starting the ELP Remote Programmer

45

Image 64

Contents Epson Page Iii Important Information About Your ELP-3300 Important Safety Information Remote Control InformationAmbient light is too bright Readme File Information Contents Using the Projector Remote Control of the Computer Troubleshooting Introduction Getting the Most Out of Your Projector Serial Communication Kit Optional Accessories About This Manual Safety Instructions Safety Instructions Where to Get Help 800Electronic support services Epson Download Service614 529-1611or your local CompuServe access number Energy Star ComplianceInstallation Unpacking the Projector Additional components Setting Up the Projector Maximum ZoomSetting Up the Projector Connecting to a Computer Connecting to a PC desktop computer Connecting to a PC laptop computer Connecting to a desktop Macintosh Connecting to a PowerBook Connecting to a Video Source Yellow Video/audio cable Connecting to an Audio Source Connecting to an External Speaker or PA System You should now adjust the Fade menu setting. SeeSetting Up Serial Communication Connecting the serial cableInstalling the software Modem port is identified by the following iconConnecting the Remote Control with the Lead Wire Installation Using the Projector Turning the Equipment On and Off Focusing and Positioning the Screen Image Using the Projector Controlling the Projector Controlling the ProjectorStandby Sync + Button/component Function Adjusting the settings from ELP Link You see a screen similar to the followingMonitoring the Projector Using Rear Projection Using the Menus Accessing the Menus Following table shows the settings for each of the menusChanging menu settings To close the menus, again press the Menu buttonAccessing ELP Link menus Menu Settings Restoring the default settingsComputer menu Lines until they disappear TrackingScreen wider than the projector’s area Video menu Display menu Blank To Blue. For a description of Blank, seeRear Proj Projection, Rear Proj should be offAudio menu Options menu Language Custom menuJapanese Using the Menus Remote Control of the Computer ELP Remote Programmer Templates Windows MacintoshStarting the ELP Remote Programmer Do the following to start the ELP Remote ProgrammerRemote Control of the Computer Element Function Assigning a Macro to a Programmable Button Using record mode Assigning a Macro to a Programmable ButtonRemote Control of the Computer Using manual mode Activating a TemplateELP Remote Programmer Menus Maintenance Cleaning the Projector Case Cleaning the LensCleaning the Air Filter Cleaning the Air Filter Cleaning the Trackball Cleaning the Trackball Replacing the Lamp Turn the projector over so you can access the lamp cover When the screws are loose, lift off the lamp coverLift up the handle and pull out the lamp Resetting the lamp timer Replacing the Fuse Replacing the Fuse Maintenance Troubleshooting Problems with the Projector Status light ColorFor specific problems, see the following Power status light does not come onTemperature status light is orange Problems with the Image or Sound An image does not appear on the screenOnly the test pattern is displayed Colors of the image are not right Problems with the Remote Control Using the trackball has no effect Troubleshooting Technical Specifications GeneralOptical Electrical Supported Monitor Displays Pin Assignments Monitor and VGA connector pin assignments Glossary Brightness. The balance of light and dark shades in an image82Glossary Glossary83 84Glossary Index 86Index Index87 88Index Index89 66-68 Tint