Epson owner manual Important Information About Your ELP-3300, Ambient light is too bright

Page 4

Important Information About Your ELP-3300

Please read the following important information about your ELP-3300 projector.

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on.

WARNING: Never open any cover on the projector, except the lamp, fuse, and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this Owners Manual, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Caution: When you replace the lamp, never touch the new bulb with your bare hands; the invisible residue left by the oil on your hands may shorten the bulb life. Use a cloth or glove to handle the new bulb.

Remote Control Information

The ELP-3300 allows you to operate it by remote control via infrared (IR) receivers located at the front and back of the projector. The projector may not respond to remote control commands under the following conditions:

• The ambient light is too bright

iii

Image 4
Contents Epson Page Iii Important Information About Your ELP-3300 Important Safety Information Remote Control InformationAmbient light is too bright Readme File Information Contents Using the Projector Remote Control of the Computer Troubleshooting Introduction Getting the Most Out of Your Projector Serial Communication Kit Optional Accessories About This Manual Safety Instructions Safety Instructions Where to Get Help 800Electronic support services Epson Download Service614 529-1611or your local CompuServe access number Energy Star ComplianceInstallation Unpacking the Projector Additional components Setting Up the Projector Maximum ZoomSetting Up the Projector Connecting to a Computer Connecting to a PC desktop computer Connecting to a PC laptop computer Connecting to a desktop Macintosh Connecting to a PowerBook Connecting to a Video Source Yellow Video/audio cable Connecting to an Audio Source Connecting to an External Speaker or PA System You should now adjust the Fade menu setting. SeeSetting Up Serial Communication Connecting the serial cableInstalling the software Modem port is identified by the following iconConnecting the Remote Control with the Lead Wire Installation Using the Projector Turning the Equipment On and Off Focusing and Positioning the Screen Image Using the Projector Controlling the Projector Controlling the ProjectorStandby Sync + Button/component Function Adjusting the settings from ELP Link You see a screen similar to the followingMonitoring the Projector Using Rear Projection Using the Menus Accessing the Menus Following table shows the settings for each of the menusChanging menu settings To close the menus, again press the Menu buttonAccessing ELP Link menus Menu Settings Restoring the default settingsComputer menu Lines until they disappear TrackingScreen wider than the projector’s area Video menu Display menu Blank To Blue. For a description of Blank, seeRear Proj Projection, Rear Proj should be offAudio menu Options menu Language Custom menuJapanese Using the Menus Remote Control of the Computer ELP Remote Programmer Templates Windows MacintoshStarting the ELP Remote Programmer Do the following to start the ELP Remote ProgrammerRemote Control of the Computer Element Function Assigning a Macro to a Programmable Button Using record mode Assigning a Macro to a Programmable ButtonRemote Control of the Computer Using manual mode Activating a TemplateELP Remote Programmer Menus Maintenance Cleaning the Projector Case Cleaning the LensCleaning the Air Filter Cleaning the Air Filter Cleaning the Trackball Cleaning the Trackball Replacing the Lamp Turn the projector over so you can access the lamp cover When the screws are loose, lift off the lamp coverLift up the handle and pull out the lamp Resetting the lamp timer Replacing the Fuse Replacing the Fuse Maintenance Troubleshooting Problems with the Projector Status light ColorFor specific problems, see the following Power status light does not come onTemperature status light is orange Problems with the Image or Sound An image does not appear on the screenOnly the test pattern is displayed Colors of the image are not right Problems with the Remote Control Using the trackball has no effect Troubleshooting Technical Specifications GeneralOptical Electrical Supported Monitor Displays Pin Assignments Monitor and VGA connector pin assignments Glossary Brightness. The balance of light and dark shades in an image82Glossary Glossary83 84Glossary Index 86Index Index87 88Index Index89 66-68 Tint