Kodak EKTAPRO instruction manual Accessories, Possible problems during operation

Possible problems during operation

3UREOHP		3RVVLEOHUHDVRQV		+HOS
After switching on, the projector is not	Fuse blown.		Check fuse and possibly replace it.
operable.			For UK users: Check 13 A plug fuse also.
Projector drive system failure (tray	1.	Jammed slide in the slide gate.	1.	Switch off projector; lift off slide tray; remove slide from the slide
transportation, slide lift)	2.	Slide tray base plate not in the zero	gate; rotate the base plate until it locks in position; replace the tray and
	position.		switch on the projector.
	3.	Slide tray base plate bent.	2.	Switch off projector; lift off slide tray, rotate the base plate until it
	4.	Partition wall of slide tray compartment	locks in position; replace tray and switch on the projector.
	bent or damaged. (Turn tray and check via		3.	Use a new slide tray.
	baseplate opening)		4.	Use a new slide tray.
Image can’t be focused by focus buttons.	1.	Lens mount was not set to its default	1.	Press focus buttons to move lens mount to its default setting. Focus the
	position.		image as indicated in the manual.
	2.	Slide is distorted	2.	Use glass mounted slides.
	3.	Slide mount is defective.	3.	Replace slide mount.
The tray cannot be fit on the tray transport	Tray transport ring not in zero position.		- Hold slide change button-backwards depressed till tray stops in zero-
ring			position or
			- switch projector off and then on again.
The tray cannot be moved.	Tray has not been placed correctly on the		Lift off the tray; switch projector on and then off again and then replace
	transport ring.		tray.
Slides are one-sided illuminated.	Condensor out of position.		Switch off the projector; pull out the lamp module and let it cool down;
			check that the condensor is correctly seated and push back into position if
			necessary.
Fan runs but lamp is switched off.	1.	Lamp failure	1.	Refer to page 21
	2.	Lamp module is not properly fixed.	2.	Refer to page 21

Note: If none of the faults listed above caused the problem, please contact your KODAK audiovisual products dealer.

Accessories

• KODAK Slide Projection FF Lenses	(lens summary, page 85)
• KODAK EKTAPRO Lens Support	European CAT No. 715 1335

•KODAK EKTAPRO 80 Slide Tray European CAT No. 712 8580

•KODAK EKTAPRO Cable Remote (4 m) European CAT No. 712 1080

•KODAK EKTAPRO Remote Extension Cable / 8 m

European CAT No. 712 5925

Up to three of these cables can be joined together.

•KODAK EKTAPRO IR Remote System RA European CAT No. 712 1072

•KODAK EKTAPRO IR Remote System RA/LP European CAT No. 712 1064

•KODAK EKTAPRO IR Remote Receiver RA European CAT No. 712 8606

This receiver is necessary for operating another projector in parallel via the EKTAPRO IR Remote Controls.

•KODAK EKTAPRO Extra Bright Single Lamp Module (with EXR 35 h lamp and stray light protection)

European CAT No. 718 4351

•KODAK EKTAPRO Standard Heatfilter for Extra Bright Lamp Modules for the reduction of slide temperature and brightness (conforms with the 3000, 3010, 4010, 7000, 9000 and 9010 models).

European CAT No. 717 7140

•KODAK EKTAPRO Heatfilter +10 for Extra Bright Lamp Modules for the reduction of slide temperature and brightness (conforms with all previous models already equipped with such filters). European CAT No. 717 7157

•Projection Lamps

EXR 82V/35h 300W	European CAT No. 145 2259
FHS 82V/70h 300W	European CAT No.	147 7678
EXY 82V/200h 250W	European CAT No.	145 2143
• KODAK EKTAPRO Carrying Case European CAT No. 718 1993
Hard case for projector, lens,	tray and remote control transportation.

•KODAK EKTAPRO Twin Socket Adapter European CAT No. 712 5909

This adapter allows linkage of an additional projector in parallel and an EKTAPRO Cable Remote. The adapter will fit into the remote control socket.

•KODAK EKTAPRO Twin Socket Connecting Cable / 2 m European CAT No. 712 5917

To connect an additional EKTAPRO Slide Projector to the Twin Socket Adapter for a projection in parallel.

•KODAK EKTAPRO 4 x 4 Condenser Kit Europ. Cat. No. 714 4967 For projecting 4 x 4 slides (superslides) for the KODAK 36, 85, 93, 100, 150 and 180 mm Projection FF Lenses!

22