Fluke 2680A, 2686A manual Contacting Fluke, Additional Information

Page 12

2680A/2686A

Getting Started Guide

Contacting Fluke

To contact Fluke, call one of the following telephone numbers:

USA: 1-888-99-FLUKE (1-888-993-5853)

Canada: 1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-675-200

Japan: +81-3-3434-0181

Singapore: +65-738-5655

Anywhere in the world: +1-425-446-5500

Or, visit Fluke’s Web site at www.fluke.com.

Additional Information

Refer to the Users Manual provided on the 268XA CD for additional information on configuring and using your 268XA series device or Fluke DAQ software.

The CD contains necessary documentation for proper use and operation of the product. If the CD is damaged or if you are unable to access product documentation on the CD, visit the Fluke Web site or contact Fluke at any of the numbers listed above.

If AutoRun is disabled, from the Start menu, select Run…, (CD-Drive letter):\launch.exe <Enter>.

2

Image 12

Contents 2680A/2686A Limited Warranty and Limitation of Liability Safety Information Interference InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Additional Safety Information SpecificationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Getting Started IntroductionContacting Fluke Additional InformationConfiguring the 268XA Reviewing and Setting the Base Channel NumberReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Reviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary displayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Installing Host Computer Ethernet Adapter Host Computer and Network PreparationSoftware Preparing for Network OperationDevice and Host Computer Interconnection Host Computer/Device Direct ConnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters Installing Fluke DAQ Software To install Fluke DAQ software on your computerInstalling Fluke DAQ Software Using the Toolbar Understanding the User InterfaceFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Checking Operational Status Device Status IconModule Status Icon Computed Channel Status IconConfiguration Dialogs Network Configuration DialogDevice Configuration Dialog Module Configuration Dialog Analog Channel Configuration DialogDIO Configuration Dialog Computed Channel Configuration DialogCommunication Dialogs Security DialogsAlarm Dialog Mail and Web Settings DialogsTrend Dialog Managing Your Network Using Fluke DAQ Inserting and Configuring a 268XA DeviceTo insert and configure a device Configuration file Group is externally wiredAdvanced Setting autodisable scan Interval 3 autoscan rate Network TypeTreeView panel, select the device you just added Configuration transfer Temperature UnitsIP Address Verify ButtonMonitor Channel Scan ParametersScan Overflow Log to PC Card 2686A onlyInserting and Configuring a Module To insert and configure a moduleModule Number Module TypeAlg109s.bmp Alarm Trigger Interval TriggerExternal Trigger Drift CorrectionStart Count DebounceDirection Inserting and Configuring a Channel To insert and configure a ChannelAlarm Type CH #Label Unit LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Use Channel as Alarm Trigger Digital OutputTrigger Scan With Module Channel a or Channel BUsing Equations with Computed Channels Alg120s.bmp Starting a Configuration Scan To start a configuration scanStarting a Scan Starting a Device Scan To start a device scanStarting a Scan Using Spy To start a Spy scanViewing Module Measurement Data To view module measurement dataUsing the Digital I/O Points Communication Dialog To view digital I/O points dialogUsing Trend to View Collected Data To use the trend featurePen TypeZoom ExportDevice ID ModuleStart Date/Start Time DurationChanging the Chart Display To change the strip chart displayViewing Alarms To view alarmsAlarm Device Filters AckPeriod of Viewing Using Fluke DAQ System Security Features To use the system security featureConfiguring Web and Alarm Mail Settings To enter web and alarm mail settingsSend alarms by e-mail UpdateData Server IP Address Uniform Resource Locator URL