Fluke 2686A, 2680A manual Reviewing and Setting the Line Frequency

Page 15

Getting Started

Configuring the 268XA

Reviewing and Setting the Line Frequency

Perform the procedure below to review or set the line frequency. Line frequency selection allows the device to optimize internal circuitry for best accuracy. (See Figure 2 for examples.)

∙Line Frequency Choices Select 50 Hz or 60 Hz as the frequency of the primary power when an ac source powers the device.

￿

￿

￿

￿

￿

￿

￿

Table 2. Reviewing and Setting the Line Frequency

Press the COMM key to review the Line Frequency setting, or press and hold the COMM key for 3 seconds to set the Line Frequency.

Press the up/down arrow keys until LinE (Line Frequency) appears in the

primary display (comm appears in the secondary display).

Press the ENTER key. LinE appears in the secondary display and the current LinE frequency setting is in the primary display.

For Line Frequency set procedures, press the up/down arrow keys to select

50 (Hz) or 60 (Hz) line frequency (current setting appears bright).

Press the ENTER key to exit. (Pressing any other function key will cancel set operations.)

5

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 2680A/2686A Limited Warranty and Limitation of Liability Interference Information Safety InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Additional Safety Information SpecificationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Introduction Getting StartedAdditional Information Contacting FlukeConfiguring the 268XA Reviewing and Setting the Base Channel NumberReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary display Reviewing and Setting the Subnet Mask and Default GatewayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Host Computer and Network Preparation Installing Host Computer Ethernet AdapterPreparing for Network Operation SoftwareHost Computer/Device Direct Connection Device and Host Computer InterconnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters To install Fluke DAQ software on your computer Installing Fluke DAQ SoftwareInstalling Fluke DAQ Software Using the Toolbar Understanding the User InterfaceFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Computed Channel Status Icon Checking Operational StatusDevice Status Icon Module Status IconConfiguration Dialogs Network Configuration DialogDevice Configuration Dialog Computed Channel Configuration Dialog Module Configuration DialogAnalog Channel Configuration Dialog DIO Configuration DialogSecurity Dialogs Communication DialogsAlarm Dialog Mail and Web Settings DialogsTrend Dialog Managing Your Network Using Fluke DAQ Inserting and Configuring a 268XA DeviceTo insert and configure a device Network Type Configuration fileGroup is externally wired Advanced Setting autodisable scan Interval 3 autoscan rateTreeView panel, select the device you just added Verify Button Configuration transferTemperature Units IP AddressLog to PC Card 2686A only Monitor ChannelScan Parameters Scan OverflowModule Type Inserting and Configuring a ModuleTo insert and configure a module Module NumberAlg109s.bmp Drift Correction Alarm TriggerInterval Trigger External TriggerStart Count DebounceDirection To insert and configure a Channel Inserting and Configuring a ChannelUnit Label Alarm TypeCH # LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Channel a or Channel B Use Channel as Alarm TriggerDigital Output Trigger Scan With ModuleUsing Equations with Computed Channels Alg120s.bmp Starting a Configuration Scan To start a configuration scanStarting a Scan To start a device scan Starting a Device ScanTo start a Spy scan Starting a Scan Using SpyTo view module measurement data Viewing Module Measurement DataTo view digital I/O points dialog Using the Digital I/O Points Communication DialogTo use the trend feature Using Trend to View Collected DataExport PenType ZoomDuration Device IDModule Start Date/Start TimeTo change the strip chart display Changing the Chart DisplayTo view alarms Viewing AlarmsAlarm Device Filters AckPeriod of Viewing To use the system security feature Using Fluke DAQ System Security FeaturesTo enter web and alarm mail settings Configuring Web and Alarm Mail SettingsUniform Resource Locator URL Send alarms by e-mailUpdate Data Server IP Address

2686A, 2680A specifications

The Fluke 2680A and 2686A are sophisticated data acquisition systems designed for versatile applications in electrical and environmental testing. These high-performance devices cater to engineers and technicians who require reliable and precise measurement capabilities.

At the heart of these instruments is their advanced modular design, which allows users to customize the system according to specific measurement needs. The Fluke 2680A offers eight channels, while the 2686A boasts an impressive 20 channels of data acquisition, thus providing flexibility for various testing scenarios. This modularity ensures that users can easily expand their measurement capabilities by adding more channels or switching between different measurement modules.

One of the standout features of the Fluke 2680A and 2686A is their ability to perform simultaneous measurements across multiple channels. This is particularly beneficial for applications that require real-time data analysis, minimizing the time spent on sequential measurements. With sample rates reaching up to 100 kS/s, these devices provide quick and accurate data collection, making them ideal for both laboratory settings and field use.

Both models incorporate advanced signal conditioning technology, enabling them to handle a wide range of input types, including voltage, current, temperature, and resistance. This capability eliminates the need for external signal conditioning equipment, streamlining the setup and reducing overall costs for users. The inclusion of built-in digital filtering and scaling further enhances measurement accuracy, ensuring reliable results even in noisy environments.

The Fluke 2680A and 2686A also feature robust connectivity options, including USB, Ethernet, and RS-232 interfaces. This promotes seamless integration into existing networks and facilitates remote monitoring and control. Additionally, both devices support various programming languages, allowing for easy automation of testing procedures.

Another highlight is the intuitive user interface that allows users to configure the device with minimal effort. An embedded web server provides remote access to the instrument, enabling users to monitor data and configure settings from anywhere.

In summary, the Fluke 2680A and 2686A stand out as premier data acquisition systems, offering exceptional modularity, versatile measurement capabilities, and advanced connectivity options. Their combination of speed, accuracy, and ease of use makes them indispensable tools for professionals in testing and measurement applications.
Top Page Image Contents