Fluke 2680A, 2686A manual TreeView panel, select the device you just added

Page 46

2680A/2686A

Getting Started Guide

4.Specify the Base Channel (1 to 99) and Device Type and click OK. A device is attached to the new configuration. As part of the insertion process, you can specify a base channel number. This number is used to differentiate channels in different devices. You can insert up to 99 Base Channels of the same Device Type. The Base Channel number auto-increments when you add devices.

alg104s.bmp

Note

Fluke DAQ also supports 2640A and 2645A NetDAQ devices. Some of the Fluke DAQ configuration dialogs may differ from those for the 268XA.

5. In the TreeView panel, select the device you just added.

alg105s.bmp

36

Image 46

Contents 2680A/2686A Limited Warranty and Limitation of Liability Safety Information Interference InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Specification Additional Safety InformationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Getting Started IntroductionContacting Fluke Additional InformationReviewing and Setting the Base Channel Number Configuring the 268XAReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Reviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary displayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Installing Host Computer Ethernet Adapter Host Computer and Network PreparationSoftware Preparing for Network OperationDevice and Host Computer Interconnection Host Computer/Device Direct ConnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters Installing Fluke DAQ Software To install Fluke DAQ software on your computerInstalling Fluke DAQ Software Understanding the User Interface Using the ToolbarFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Module Status Icon Checking Operational StatusDevice Status Icon Computed Channel Status IconNetwork Configuration Dialog Configuration DialogsDevice Configuration Dialog DIO Configuration Dialog Module Configuration DialogAnalog Channel Configuration Dialog Computed Channel Configuration DialogCommunication Dialogs Security Dialogs Mail and Web Settings Dialogs Alarm Dialog Trend Dialog Inserting and Configuring a 268XA Device Managing Your Network Using Fluke DAQTo insert and configure a device Advanced Setting autodisable scan Interval 3 autoscan rate Configuration fileGroup is externally wired Network TypeTreeView panel, select the device you just added IP Address Configuration transferTemperature Units Verify ButtonScan Overflow Monitor ChannelScan Parameters Log to PC Card 2686A onlyModule Number Inserting and Configuring a ModuleTo insert and configure a module Module TypeAlg109s.bmp External Trigger Alarm TriggerInterval Trigger Drift CorrectionDebounce Start CountDirection Inserting and Configuring a Channel To insert and configure a ChannelLabel Alarm TypeCH # Unit LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Trigger Scan With Module Use Channel as Alarm TriggerDigital Output Channel a or Channel BUsing Equations with Computed Channels Alg120s.bmp To start a configuration scan Starting a Configuration ScanStarting a Scan Starting a Device Scan To start a device scanStarting a Scan Using Spy To start a Spy scanViewing Module Measurement Data To view module measurement dataUsing the Digital I/O Points Communication Dialog To view digital I/O points dialogUsing Trend to View Collected Data To use the trend featureZoom PenType ExportStart Date/Start Time Device IDModule DurationChanging the Chart Display To change the strip chart displayViewing Alarms To view alarmsAck Alarm Device FiltersPeriod of Viewing Using Fluke DAQ System Security Features To use the system security featureConfiguring Web and Alarm Mail Settings To enter web and alarm mail settingsData Server IP Address Send alarms by e-mailUpdate Uniform Resource Locator URL