Fluke 2680A, 2686A manual Xwwarning Do not Operate in Explosive Atmospheres

Page 6

XWWARNING

DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES

To avoid personal injury or death, do not remove the device cover without first removing the power source connected to the rear panel. Do not operate the device without the cover properly installed. There is no need for the operator to remove the cover.

DO NOT ATTEMPT TO OPERATE IF PROTECTION MAY BE IMPAIRED

If the device appears damaged or operates abnormally, protection may be impaired. Do not attempt to operate the device under these conditions. Refer all question of proper device operation to qualified service personnel.

DO NOT ATTEMPT TO SERVICE UNLESS YOU ARE A

FLUKE QUALIFIED REPAIR TECHNICIAN

To avoid personal injury or death, remove the AC power cord and all analog and digital connector modules before servicing the device.

Note

All signals must be removed from the analog and digital connector wiring before opening the connector modules.

iv

Image 6

Contents 2680A/2686A Limited Warranty and Limitation of Liability Safety Information Interference InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Additional Safety Information SpecificationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Getting Started IntroductionContacting Fluke Additional InformationConfiguring the 268XA Reviewing and Setting the Base Channel NumberReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Reviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary displayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Installing Host Computer Ethernet Adapter Host Computer and Network PreparationSoftware Preparing for Network OperationDevice and Host Computer Interconnection Host Computer/Device Direct ConnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters Installing Fluke DAQ Software To install Fluke DAQ software on your computerInstalling Fluke DAQ Software Using the Toolbar Understanding the User InterfaceFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Module Status Icon Checking Operational StatusDevice Status Icon Computed Channel Status IconConfiguration Dialogs Network Configuration DialogDevice Configuration Dialog DIO Configuration Dialog Module Configuration DialogAnalog Channel Configuration Dialog Computed Channel Configuration DialogCommunication Dialogs Security DialogsAlarm Dialog Mail and Web Settings DialogsTrend Dialog Managing Your Network Using Fluke DAQ Inserting and Configuring a 268XA DeviceTo insert and configure a device Advanced Setting autodisable scan Interval 3 autoscan rate Configuration fileGroup is externally wired Network TypeTreeView panel, select the device you just added IP Address Configuration transferTemperature Units Verify ButtonScan Overflow Monitor ChannelScan Parameters Log to PC Card 2686A onlyModule Number Inserting and Configuring a ModuleTo insert and configure a module Module TypeAlg109s.bmp External Trigger Alarm TriggerInterval Trigger Drift CorrectionStart Count DebounceDirection Inserting and Configuring a Channel To insert and configure a ChannelLabel Alarm TypeCH # Unit LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Trigger Scan With Module Use Channel as Alarm TriggerDigital Output Channel a or Channel BUsing Equations with Computed Channels Alg120s.bmp Starting a Configuration Scan To start a configuration scanStarting a Scan Starting a Device Scan To start a device scanStarting a Scan Using Spy To start a Spy scanViewing Module Measurement Data To view module measurement dataUsing the Digital I/O Points Communication Dialog To view digital I/O points dialogUsing Trend to View Collected Data To use the trend featureZoom PenType ExportStart Date/Start Time Device IDModule DurationChanging the Chart Display To change the strip chart displayViewing Alarms To view alarmsAlarm Device Filters AckPeriod of Viewing Using Fluke DAQ System Security Features To use the system security featureConfiguring Web and Alarm Mail Settings To enter web and alarm mail settingsData Server IP Address Send alarms by e-mailUpdate Uniform Resource Locator URL