Fluke 2680A, 2686A manual Examples for Reviewing and Setting the BCN

Page 14

2680A/2686A

Getting Started Guide

REVIEW

Communications display for reviewing the Base Channel Number (BCN)

SET

Communications display for setting the BCN

SET

Base Channel Number display for setting the BCN 10s digits (for example, 45)

REVIEW

Base Channel Number display for reviewing the BCN number (for example, 45)

CH

Front Panel display for an device with BCN 45

Figure 1. Examples for Reviewing and Setting the BCN

4

Image 14

Contents 2680A/2686A Limited Warranty and Limitation of Liability Safety Information Interference InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres General Specifications Characteristic Additional Safety InformationSpecification Page Table of Contents 2680A/2686A Getting Started IntroductionContacting Fluke Additional InformationReviewing and Setting the Base Channel Number Configuring the 268XAReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Reviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary displayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Installing Host Computer Ethernet Adapter Host Computer and Network PreparationSoftware Preparing for Network OperationDevice and Host Computer Interconnection Host Computer/Device Direct ConnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters Installing Fluke DAQ Software To install Fluke DAQ software on your computerInstalling Fluke DAQ Software Fluke DAQ Toolbar Buttons Function Using the ToolbarUnderstanding the User Interface Understanding the User Interface Understanding the Workspace Area Module Status Icon Checking Operational StatusDevice Status Icon Computed Channel Status IconDevice Configuration Dialog Configuration DialogsNetwork Configuration Dialog DIO Configuration Dialog Module Configuration DialogAnalog Channel Configuration Dialog Computed Channel Configuration DialogCommunication Dialogs Security DialogsTrend Dialog Alarm DialogMail and Web Settings Dialogs To insert and configure a device Managing Your Network Using Fluke DAQInserting and Configuring a 268XA Device Advanced Setting autodisable scan Interval 3 autoscan rate Configuration fileGroup is externally wired Network TypeTreeView panel, select the device you just added IP Address Configuration transferTemperature Units Verify ButtonScan Overflow Monitor ChannelScan Parameters Log to PC Card 2686A onlyModule Number Inserting and Configuring a ModuleTo insert and configure a module Module TypeAlg109s.bmp External Trigger Alarm TriggerInterval Trigger Drift CorrectionDirection Start CountDebounce Inserting and Configuring a Channel To insert and configure a ChannelLabel Alarm TypeCH # Unit LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Trigger Scan With Module Use Channel as Alarm TriggerDigital Output Channel a or Channel BUsing Equations with Computed Channels Alg120s.bmp Starting a Scan Starting a Configuration ScanTo start a configuration scan Starting a Device Scan To start a device scanStarting a Scan Using Spy To start a Spy scanViewing Module Measurement Data To view module measurement dataUsing the Digital I/O Points Communication Dialog To view digital I/O points dialogUsing Trend to View Collected Data To use the trend featureZoom PenType ExportStart Date/Start Time Device IDModule DurationChanging the Chart Display To change the strip chart displayViewing Alarms To view alarmsPeriod of Viewing Alarm Device FiltersAck Using Fluke DAQ System Security Features To use the system security featureConfiguring Web and Alarm Mail Settings To enter web and alarm mail settingsData Server IP Address Send alarms by e-mailUpdate Uniform Resource Locator URL