Fluke 2686A, 2680A manual Safety Information, Interference Information

Page 3

Safety Information

WCaution

This is an IEC safety Class 1 product. Before using, the ground wire in the line cord or rear panel binding post must be connect to an earth ground for safety.

Interference Information

This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.

Operation is subject to the following two conditions:

∙This device may not cause harmful interference.

∙This device must accept any interference received, including interference that may cause undesired operation.

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:

∙Reorient the receiving antenna

∙Relocate the equipment with respect to the receiver

∙Move the equipment away from the receiver

∙Plug the equipment into a different outlet so that the computer and receiver are on different branch circuits

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No. 004-000-00345-4.

i

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 2680A/2686A Limited Warranty and Limitation of Liability Interference Information Safety InformationSafety Terms in this Manual Xwwarning Xwwarning Do not Operate in Explosive Atmospheres Additional Safety Information SpecificationGeneral Specifications Characteristic Page Table of Contents 2680A/2686A Introduction Getting StartedAdditional Information Contacting FlukeConfiguring the 268XA Reviewing and Setting the Base Channel NumberReviewing and Setting the Base Channel Number Examples for Reviewing and Setting the BCN Reviewing and Setting the Line Frequency Reviewing and Setting the Line FrequencyExamples for Reviewing and Setting the Line Frequency Reviewing and Setting the Network Type Reviewing and Setting the Network TypeExamples for Reviewing and Setting the Network Type Reviewing and Setting the Network Type to General Communications display for reviewing the network type IP address display for setting an IP0 digit for example Reviewing and Setting the General Network Socket Port Reviewing and Setting the General Network Socket PortReviewing and Setting the General Network IP Address Reviewing and Setting the General Network IP AddressReviewing and Setting the Subnet Mask and Default Gateway Appears in the secondary display Reviewing and Setting the Subnet Mask and Default GatewayViewing the Device Ethernet Address Viewing the Device Ethernet AddressExamples for Viewing the Ethernet Address Host Computer and Network Preparation Installing Host Computer Ethernet AdapterPreparing for Network Operation SoftwareHost Computer/Device Direct Connection Device and Host Computer InterconnectionInterconnection Using 10/100BaseT Twisted Pair Wiring Installing Host Computer Networking Software Setting Host Computer Networking Parameters To install Fluke DAQ software on your computer Installing Fluke DAQ SoftwareInstalling Fluke DAQ Software Using the Toolbar Understanding the User InterfaceFluke DAQ Toolbar Buttons Function Understanding the User Interface Understanding the Workspace Area Computed Channel Status Icon Checking Operational StatusDevice Status Icon Module Status IconConfiguration Dialogs Network Configuration DialogDevice Configuration Dialog Computed Channel Configuration Dialog Module Configuration DialogAnalog Channel Configuration Dialog DIO Configuration DialogSecurity Dialogs Communication DialogsAlarm Dialog Mail and Web Settings DialogsTrend Dialog Managing Your Network Using Fluke DAQ Inserting and Configuring a 268XA DeviceTo insert and configure a device Network Type Configuration fileGroup is externally wired Advanced Setting autodisable scan Interval 3 autoscan rateTreeView panel, select the device you just added Verify Button Configuration transferTemperature Units IP AddressLog to PC Card 2686A only Monitor ChannelScan Parameters Scan OverflowModule Type Inserting and Configuring a ModuleTo insert and configure a module Module NumberAlg109s.bmp Drift Correction Alarm TriggerInterval Trigger External TriggerStart Count DebounceDirection To insert and configure a Channel Inserting and Configuring a ChannelUnit Label Alarm TypeCH # LabelConfiguring a Computed Channel Alg117s.bmp Computed channels are assigned channel numbers from 901 to Channel a or Channel B Use Channel as Alarm TriggerDigital Output Trigger Scan With ModuleUsing Equations with Computed Channels Alg120s.bmp Starting a Configuration Scan To start a configuration scanStarting a Scan To start a device scan Starting a Device ScanTo start a Spy scan Starting a Scan Using SpyTo view module measurement data Viewing Module Measurement DataTo view digital I/O points dialog Using the Digital I/O Points Communication DialogTo use the trend feature Using Trend to View Collected DataExport PenType ZoomDuration Device IDModule Start Date/Start TimeTo change the strip chart display Changing the Chart DisplayTo view alarms Viewing AlarmsAlarm Device Filters AckPeriod of Viewing To use the system security feature Using Fluke DAQ System Security FeaturesTo enter web and alarm mail settings Configuring Web and Alarm Mail SettingsUniform Resource Locator URL Send alarms by e-mailUpdate Data Server IP Address

2686A, 2680A specifications

The Fluke 2680A and 2686A are sophisticated data acquisition systems designed for versatile applications in electrical and environmental testing. These high-performance devices cater to engineers and technicians who require reliable and precise measurement capabilities.

At the heart of these instruments is their advanced modular design, which allows users to customize the system according to specific measurement needs. The Fluke 2680A offers eight channels, while the 2686A boasts an impressive 20 channels of data acquisition, thus providing flexibility for various testing scenarios. This modularity ensures that users can easily expand their measurement capabilities by adding more channels or switching between different measurement modules.

One of the standout features of the Fluke 2680A and 2686A is their ability to perform simultaneous measurements across multiple channels. This is particularly beneficial for applications that require real-time data analysis, minimizing the time spent on sequential measurements. With sample rates reaching up to 100 kS/s, these devices provide quick and accurate data collection, making them ideal for both laboratory settings and field use.

Both models incorporate advanced signal conditioning technology, enabling them to handle a wide range of input types, including voltage, current, temperature, and resistance. This capability eliminates the need for external signal conditioning equipment, streamlining the setup and reducing overall costs for users. The inclusion of built-in digital filtering and scaling further enhances measurement accuracy, ensuring reliable results even in noisy environments.

The Fluke 2680A and 2686A also feature robust connectivity options, including USB, Ethernet, and RS-232 interfaces. This promotes seamless integration into existing networks and facilitates remote monitoring and control. Additionally, both devices support various programming languages, allowing for easy automation of testing procedures.

Another highlight is the intuitive user interface that allows users to configure the device with minimal effort. An embedded web server provides remote access to the instrument, enabling users to monitor data and configure settings from anywhere.

In summary, the Fluke 2680A and 2686A stand out as premier data acquisition systems, offering exceptional modularity, versatile measurement capabilities, and advanced connectivity options. Their combination of speed, accuracy, and ease of use makes them indispensable tools for professionals in testing and measurement applications.
Top Page Image Contents