Emerson AMC-S402 manual Front Panel Indicators, Color, State, Function

Page 29

6 Front Panel Indicators

The faceplate of the AMC-S402 module has three LED indicators. The figure and table that follows describes the function of each.

Figure 6. AMC Front Panel Indicators

Table 11 LED Function

Indicator	Color	State	Function

Hot Swap (HS)	BLUE	On	Management power available to the module
			and the module can safely be extracted

		Off	The module is operational and is unsafe for
			extraction

		Long Blink	Delay before module is activated

		Short Blink	Delay before module is de-activated

Fault or “Out of Service” (OOS)	RED	On	Module Fault set by Shelf manager or
			12V payload power not detected.

		Off	No module fault
			12V payload power is being supplied to board

Module In Service (IS)	GREEN	On	12V payload power is being supplied to board

		Blink	Indicates SAS disk I/O activity

		Off	12V payload power is not detected

6806800H60A AMC-S402 Installation and Use

Image 29

Contents 6806800H60A March Installation and UseAMC-S402 Trademarks 2009 Emerson All rights reservedLimited and Restricted Rights Legend Contact Address2.2.1 Contents2.3.1 2.4.1SPECIFICATIONS 7.2.1FRONT PANEL INDICATORS IPMI FIRMWARE UPGRADE PROCEDUREList of Tables List of FiguresPreface Safety SummaryFlammability Safety StatementEMI Caution CE Notice European CommunityAbout This Manual commands, options and arguments to commands, andHow This Manual is Organized Conventions Used in This Manualcourier introduce new termsSystem output for example, screen displays and reports examples, and system promptsUnpacking Instructions Hardware Preparation and InstallationAntistatic Precautions 1.2 PICMG Standards Compliance 1.1 Features of the AMC Module1.3 Products Supported by this Manual 1 AMC-S402 OverviewAMC-S402 Overview 1.4 Part Number, Serial Number LabelsSub-Assembly Number Final Assembly Number5 Safety Label Serial Number2.1 Installation and Removal of the AMC-S402 Module 2 AMC-S402 Installation2.2.1 Safety Statement 2.3 Before You Install or Remove the AMC2.3.2 Watch for Bent Pins or Other Damage 2.3.1 Observe ESD Precautions2.4 Use Caution When Installing or Removing AMC AMC-S402 Installation2.6 Module Hot-Swap 2.4.2 Understand Hot Swap2.5 Verify Slot Usage 2.7 Installing the AMC Module 2.8 Removing the AMC Module 3.1 Overview 3 Functional Description3.2 AMC-S402, Top Level Board Layout Power Regulator MMCFunctional Description 3.3 Serial Storage I/O Interfaces3.3.1 SAS Port Isolation Multiplexor Circuit 3.5 IPMI Subsystem 3.4 Power Regulator4.2 AMC Connector, “Finger” Assignments 4 Connector Pin Assignments4.1 AMC-S402 Port Assignments AMC.3 Serial Storage Port AMC.3 Serial Storage PortTable 6 AMC-S402 Module Edge, Pin Assignments Connector Pin AssignmentsSignal Name 5.1.1 AMC Module Height Exceptions 5 Specifications5.1 Physical Characteristics Specifications 5.2 Hard Drive Operation and Storage Specifications5.4 EMC Compliance 5.3 Power RequirementsPart number AMC-S402xxxYes, Class A ITE emissions requirements Australia Table 10 EMC Emission CompliancyEurope Commercial EN 61000-4-4 Indicator 6 Front Panel IndicatorsColor State7.2 Sensor Data Records 7 IPMI Functions List7.1 IPMI and Management Controller IPMC IPMI Functions List 7.2.1 AMC Port AssignmentsIPMI Function List 7.3 Supported IPMI CommandsIPMI Function List 8.1 The ipmitool utility 8 IPMI Firmware Upgrade ProcedureSYNOPSIS DESCRIPTIONIPMI Firmware Upgrade Procedure COMMAND SYNTAX EXAMPLES