Emerson AMC-S402 manual IPMI Firmware Upgrade Procedure COMMAND SYNTAX EXAMPLES

Page 35

IPMI Firmware Upgrade Procedure

COMMAND SYNTAX EXAMPLES

EXAMPLE 1. The following example shows the command sequence for firmware upgrade of an AMC installed on a carrier:

$ ipmitool -I lan -H 192.168.0.2 -T 0x82 -B 0 -t 0x74 -b 7 hpm upgrade hpm1fw.img $ ipmitool -I lan -H 192.168.0.2 -T 0x82 -B 0 -t 0x74 -b 7 hpm activate

Line 1 puts the new firmware in the flash device, where hpm1fw.img is the image. Line 2 is used to dynamically load and activate the new firmware.

EXAMPLE 2. The following example shows the command performing firmware upgrade on the carrier itself:

$ ipmitool -I lan -H 192.168.0.2 -t 0x82 -b 0 hpm upgrade hpm1fw.img $ ipmitool -I lan -H 192.168.0.2 -t 0x82 -b 0 hpm activate

Line 1 puts the new firmware in the flash device, where hpm1fw.img is the image. Line 2 is used to dynamically load and activate the new firmware.

6806800H60A AMC-S402 Installation and Use

Image 35

Contents 6806800H60A March Installation and UseAMC-S402 Contact Address 2009 Emerson All rights reservedTrademarks Limited and Restricted Rights Legend2.4.1 Contents2.2.1 2.3.1IPMI FIRMWARE UPGRADE PROCEDURE 7.2.1SPECIFICATIONS FRONT PANEL INDICATORSList of Tables List of FiguresPreface Safety SummaryCE Notice European Community Safety StatementFlammability EMI CautionConventions Used in This Manual commands, options and arguments to commands, andAbout This Manual How This Manual is Organizedexamples, and system prompts introduce new termscourier System output for example, screen displays and reportsUnpacking Instructions Hardware Preparation and InstallationAntistatic Precautions 1 AMC-S402 Overview 1.1 Features of the AMC Module1.2 PICMG Standards Compliance 1.3 Products Supported by this ManualAMC-S402 Overview 1.4 Part Number, Serial Number LabelsSerial Number Final Assembly NumberSub-Assembly Number 5 Safety Label2.3 Before You Install or Remove the AMC 2 AMC-S402 Installation2.1 Installation and Removal of the AMC-S402 Module 2.2.1 Safety StatementAMC-S402 Installation 2.3.1 Observe ESD Precautions2.3.2 Watch for Bent Pins or Other Damage 2.4 Use Caution When Installing or Removing AMC2.6 Module Hot-Swap 2.4.2 Understand Hot Swap2.5 Verify Slot Usage 2.7 Installing the AMC Module 2.8 Removing the AMC Module Power Regulator MMC 3 Functional Description3.1 Overview 3.2 AMC-S402, Top Level Board LayoutFunctional Description 3.3 Serial Storage I/O Interfaces3.3.1 SAS Port Isolation Multiplexor Circuit 3.5 IPMI Subsystem 3.4 Power RegulatorAMC.3 Serial Storage Port AMC.3 Serial Storage Port 4 Connector Pin Assignments4.2 AMC Connector, “Finger” Assignments 4.1 AMC-S402 Port AssignmentsTable 6 AMC-S402 Module Edge, Pin Assignments Connector Pin AssignmentsPin# 5.1.1 AMC Module Height Exceptions 5 Specifications5.1 Physical Characteristics Specifications 5.2 Hard Drive Operation and Storage SpecificationsAMC-S402xxx 5.3 Power Requirements5.4 EMC Compliance Part numberYes, Class A ITE emissions requirements Australia Table 10 EMC Emission CompliancyEurope Commercial EN 61000-4-4 State 6 Front Panel IndicatorsIndicator Color7.2 Sensor Data Records 7 IPMI Functions List7.1 IPMI and Management Controller IPMC IPMI Functions List 7.2.1 AMC Port AssignmentsIPMI Function List 7.3 Supported IPMI CommandsAMC Spec DESCRIPTION 8 IPMI Firmware Upgrade Procedure8.1 The ipmitool utility SYNOPSISIPMI Firmware Upgrade Procedure COMMAND SYNTAX EXAMPLES