Emerson manual Connector Pin Assignments, AMC-S402 Module Edge, Pin Assignments

Page 23

Connector Pin Assignments

Table 6 AMC-S402 Module Edge, Pin Assignments

Pin#	Signal Name	Pin#	Signal Name

1	GND	86	GND

2	12V	87	No Connect

3	'PRSNT1_L'	88	No Connect

4	'AMC_VCC3'	89	GND

5	GA0	90	No Connect

6	No Connect	91	No Connect

7	GND	92	GND

8	No Connect	93	No Connect

9	12V	94	No Connect

10	GND	95	GND

11	No Connect	96	No Connect

12	No Connect	97	No Connect

13	GND	98	GND

14	No Connect	99	No Connect

15	No Connect	100	No Connect

16	GND	101	GND

17	GA1	102	No Connect

18	12V	103	No Connect

19	GND	104	GND

20	No Connect	105	No Connect

21	No Connect	106	No Connect

22	GND	107	GND

23	No Connect	108	No Connect

24	No Connect	109	No Connect

25	GND	110	GND

26	GA2	111	No Connect

27	12V	112	No Connect

28	GND	113	GND

29	'TX_SATA_2+'	114	No Connect

30	'TX_SATA_2-'	115	No Connect

31	GND	116	GND

32	'RX_SATA_2+'	117	No Connect

33	'RX_SATA_2-'	118	No Connect

34	GND	119	GND

35	'TX_SATA_3+'	120	No Connect

36	'TX_SATA_3-'	121	No Connect

37	GND	122	GND

38	'RX_SATA_3+'	123	No Connect

39	'RX_SATA_3-'	124	No Connect

40	GND	125	GND

41	'AMC_ENABLE_L'	126	No Connect

42	12V	127	No Connect

43	GND	128	GND

44	No Connect	129	No Connect

45	No Connect	130	No Connect

46	GND	131	GND

6806800H60A AMC-S402 Installation and Use

13

Image 23

Contents 6806800H60A March Installation and UseAMC-S402 Contact Address 2009 Emerson All rights reservedTrademarks Limited and Restricted Rights Legend2.4.1 Contents2.2.1 2.3.1IPMI FIRMWARE UPGRADE PROCEDURE 7.2.1SPECIFICATIONS FRONT PANEL INDICATORSList of Tables List of FiguresPreface Safety SummaryCE Notice European Community Safety StatementFlammability EMI CautionConventions Used in This Manual commands, options and arguments to commands, andAbout This Manual How This Manual is Organizedexamples, and system prompts introduce new termscourier System output for example, screen displays and reportsUnpacking Instructions Hardware Preparation and InstallationAntistatic Precautions 1 AMC-S402 Overview 1.1 Features of the AMC Module1.2 PICMG Standards Compliance 1.3 Products Supported by this ManualAMC-S402 Overview 1.4 Part Number, Serial Number LabelsSerial Number Final Assembly NumberSub-Assembly Number 5 Safety Label2.3 Before You Install or Remove the AMC 2 AMC-S402 Installation2.1 Installation and Removal of the AMC-S402 Module 2.2.1 Safety StatementAMC-S402 Installation 2.3.1 Observe ESD Precautions2.3.2 Watch for Bent Pins or Other Damage 2.4 Use Caution When Installing or Removing AMC2.6 Module Hot-Swap 2.4.2 Understand Hot Swap2.5 Verify Slot Usage 2.7 Installing the AMC Module 2.8 Removing the AMC Module Power Regulator MMC 3 Functional Description3.1 Overview 3.2 AMC-S402, Top Level Board LayoutFunctional Description 3.3 Serial Storage I/O Interfaces3.3.1 SAS Port Isolation Multiplexor Circuit 3.5 IPMI Subsystem 3.4 Power RegulatorAMC.3 Serial Storage Port AMC.3 Serial Storage Port 4 Connector Pin Assignments4.2 AMC Connector, “Finger” Assignments 4.1 AMC-S402 Port AssignmentsTable 6 AMC-S402 Module Edge, Pin Assignments Connector Pin AssignmentsPin# 5.1.1 AMC Module Height Exceptions 5 Specifications5.1 Physical Characteristics Specifications 5.2 Hard Drive Operation and Storage SpecificationsAMC-S402xxx 5.3 Power Requirements5.4 EMC Compliance Part numberYes, Class A ITE emissions requirements Australia Table 10 EMC Emission CompliancyEurope Commercial EN 61000-4-4 State 6 Front Panel IndicatorsIndicator Color7.2 Sensor Data Records 7 IPMI Functions List7.1 IPMI and Management Controller IPMC IPMI Functions List 7.2.1 AMC Port AssignmentsIPMI Function List 7.3 Supported IPMI CommandsAMC Spec DESCRIPTION 8 IPMI Firmware Upgrade Procedure8.1 The ipmitool utility SYNOPSISIPMI Firmware Upgrade Procedure COMMAND SYNTAX EXAMPLES