Philips 27964-01A user manual Parts List

Page 34
Parts List

Parts List

This is a list of parts which may be replaced by the consumer. Care should be taken when replacing anything related to electrical wiring. We recom- mend contacting a professional electrician. When calling for parts, first state your bed model as S- 30SV, S-30SV3F, S-32SV or S-32SV3F, depending on the model. Then refer to this list and preceding illustrations for proper part identification.

Acrylic, Bench Acrylic, Canopy* Ballast (220VAC, 100W) Ballast (220VAC, 400W) Bushing, Bronze 10mm* Body Fan Kit* (optional) Canopy Mounting Arm Capacitor, 75uF Contactor (240VAC, 30A) Cover, Bench

Cover, Canopy

Current Sensor Endcap, Kit (with inserts) Fan, 4” (220VAC, 110cfm) Gas Spring Cover Panel* Gas Spring Set*

Handle

Hardware Kit, Complete* Hardware Kit, Assembly* Hour Counter*

Ignitor (Starter for Face Tanner) Lamp Holder w/ Starter Holder Lamp Holder w/o Starter Holder Lamp Holder, Face Tanner* Lamps*

Pillow*

Profile, Blank*

Remote Connection PCB Remote Control Bypass Plug* Schematic Packet* Silk-screened Profile, English Silk-screened Profile, French Skirt Panel

Starter, K-12(main lamps) Thermostat* (for face tanner) Timer, ADI-HT

Timer Keypad, ADI-HT* Timer Keypad Pushbuttons* Trim Profile, Gray

Wiring Harness, RJ-11 120”

Wiring Harness, Remote PCB to Timer (36”)

* Not shown

Record this information for ease of service:

Date of purchase:

Bench serial number:

Canopy serial number:

27964-01A

Image 34
Contents USER MANUAL 27964-01A24 MONTH “SILVER MEDAL” WARRANTY ETS, LLC 7445 Company Drive, Indianapolis, INSafety Information Installation elcomeontents Care and MaintenanceMAXIMUM EXPOSURE TIME IS 20 MINUTES afety InformationRECOMMENDED EXPOSURE TIMES IN MINUTES Velocity Wolff Model VEL 71-T12-100WVelocity Wolff Modèle VEL 71-T12-100W Renseignements sur la SécuritéTEMPS D’EXPOSITION RECOMMANDÉ EN MINUTES LE TEMPS D’EXPOSITION MAXIMAL EST DE 20 MINUTESUnpacking and Inspection nstallationTools Required Pre-Installation Planning Installation - Pre-Installation PlanningInstallation - Hardware Inventory Hardware InventoryInstallation - Assembly Procedures Assembly ProceduresLower Clevis Fork Assembly Stand Upright Assembly LOCKNUT others hidden STAND UPRIGHT MACHINE SCREWS 27964-01ACanopy Installation 1. Have a helper hold the canopy in its Install Gas Springs3. Screw the upper clevis forks onto the gas springsAttach Gas Springs Attach Cover Panels Attaching Handle to Canopy CENTER INSERT27964 -01A Body Fan AssemblyShock hazard Be sure power is disconnected before installing body fan body fan sold separatelyInstallation - Electrical Connections Electrical ConnectionsT-Max Products T-Max Wireless Remote SystemRemote Connections Remote System Hook-up ScenariosScenario 2 - T-Max 3A with Wireless Installation - Remote ConnectionsScenario 1 - T-Max Manager Series with Complete Wireless Scenario 3 - T-Max Manager Series with Wireless comboScenario 5 - T-Max Manager Series with wires Scenario 4 - T-Max Manager Series with Wireless comboScenario 6 - Single Bed wired to T-Max 3A Setting the “id” Setting the sunbed address manually1-99 100-199 Exposure Times perationBefore You Tan DANGEROperation - Using Your Sunbed Using Your SunbedA BC D E F G body using the canopy handle. See Safety Thorough Periodic Cleaning are and MaintenanceCleaning After Use Cleaning the Canopy and BenchCare and Maintenance - Lamp and Acrylic Replacement Lamp and Acrylic ReplacementRemoving/Replacing Acrylic Shield Removing/Replacing Lamps Recommended Replacement LampsRecommended Replacement Acrylics Velocity Wolff Model VEL 71-T12-100WRemoving/Replacing Face Tanner Lamp if equipped DANGERroubleshooting ProblemSolution Clean sunbed, see Thorough Periodic CleaningTroubleshooting ConnectionsMy bed is connected to a T-Max Remote ConnectionsS-32SV S-30SVS-30SV3F S-32SV3F Parts List SUNVISION Elite 30 3F32SV32SV3F