Xerox FS 5250 IPC instruction manual Current emulation is, Non-IPDS Selection Emulation

Page 17

Connections and Installation

Xerox FS 5250, User’s Guide

4.When the Xerox FS 5250 is ready, it will eject a page with the follo wing message:

"Current emulation is xxxx"

5.Set the desired emulation by turning the address switch to the position defined in the chart in the following:

Non-IPDS
Selection	Emulation
*0	3812/5219/3816
1	5224
2	5225
3	5256
4	4234
5	3812/5219/3816
6	4245/6262

*default value

SCS printers

IPDS

Selection Emulation

03812/5219/3816

15224

25225

35256

44234

*5	IPDS
6	4245/6262

6.A new message stating the current emulation will be printed after a few seconds. Then power off the Xerox FS 5250.

7.Power on the Xerox FS 5250.

8.Turn to the "T" position again and check that the emulation has been changed. (See the settings printout). See TEST Function.

9.Turn the switch back to the correct device address (consult your system administrator if necessary).

10.Connect the twinax cable and power on the Xerox FS 5250 or follow the procedure for setting the address via the switch. See the following section.

Check whether the configuration complies with the requirements of your installation and print jobs.

NOTE: Make sure that you have set the address switch before you switch power on.

- 17 -

Image 17

Contents Trademarks EMC directiveSafety Notice Table of Contents PCL Programming via Shareport PC Support Virtual Printer Error MessagesAppendix a Supported Setup Functions Printer Driver Selection What is the Xerox FS 5250?Introduction to the Xerox FS XES mode selection handles Xdpm and Xppm data streams Items Supplied IPC Upgrade KitIf equipped with the optional IPC module Product FeaturesNon-IPC Supported Control Units Pre-Installation Requirements Installation RequirementsNational Language Via the LineWorking Environment EU or US Settings= PCL, B = XES Connections and Installation of the Xerox FSRear Panel Twinax Connector Changing the Driver EmulationVia the Line Selecting emulation via the line can be done inPCL only%Y37,5224% Via the Address SwitchNon-IPDS Y37,n1 Write Emulation Y37,n1 Write EmulationSelection Emulation Current emulation isNon-IPDS Selection Emulation Dual Printer Emulation PCL only Address SettingVia the address switch Ipds as primary emulation Non-IPDS as primary emulationUpgrading to Ipds Connecting via Centronics output Connecting the Xerox FS 5250to the PrinterWhat if the CU Indicator fails to turn on? Connecting the Xerox FS 5250to the SystemTest Function Test via the address switchTimeout Top Panel of the Xerox FS Operation of the Xerox FS1 CU PAR Parallel inputState Indication SER Serial input/outputReady Printer Ready Yfunction number,parameters% Function Selection via the LineSyntax of an FSL Function Escape Character Removing Temporary Escape Character Defining a Temporary Escape Character??% ??blankRemoving Permanent Escape Character Defining a Permanent Escape CharacterY48,00 ??% Command Description Example Commands for Storing and Restoring Settings??% %X1 ??% %X3PCL only Pass-Through Mode%1B %%1B%Pass-through mode XES For details refer to the programmers guide, doc. D62081 Transparency Mode LimitationsIdaSetup Ipds Programming Programming the Xerox FS 5250 Non-IPDS Paper Size Selected FSL FunctionsTrays Changing paper sizeValue Paper Tray ??% %Y12,n1,n2% &&??spaceValue Paper Size Other commands Saving the commandThis command also erases the escape character Changing paper size exampleChanging paper trays Paper TraysBasic printer set-up Format Value n1 Format CharacteristicsFormats Function Y10 Page FormatValue n2 Tray Changing Page Format??% %Y10,n1,n2% &&??space ??% %Y10,2,3% %X1 Changing page format exampleFunction Y98 Automatic Page Orientation Automatic Page OrientationY98 Syntax Y98,n1,n2% Example Y98, 0,3%Automatic Page Orientation Automatic Page Orientation ChartY98 Enabled factory default Explanation to the chart on Automatic Page OrientationFonts Y98 DisabledSelecting Fonts PCL System /36 OCL Text -YES??% %Y96,n1% &&??space Changing fontSymbol SET and Translate Default Gfid TableGfid Typeface ID PCL No Name of Typeface Scaleable FontsOnly applies to printers running PCL Level Defining Fonts PCL Style StrokeweightWhat you need to know Symbol set of the fontValue Symbol set Italic This is HelveticaProportional spacing, bold Selected FSL Functions Xerox FS 5250, User’s Guide ValueTypeface Typeface of the font Value TypefaceSelecting Fonts XES Other commandsFont definition example ??% %Y91,521,6,5,1,18,1% %X1??% %Y96,41% &&?? This function cannot be saved in the permanent memoryChanging font example Font definition Defining Fonts XESFont strings sent Orientation XES GfidGfid Gfid COR CPI / Gfid Relation Optional ScalingCPI / Gfid Relation Font definition example What to consider Duplex PrintingSystem or interface? ??% Y19,0% &&?? Binding option??% X4 &&?? You cannot save the duplex command in the permanent memory Setting DescriptionSelecting duplex printing Orientation??% %Y19,2% %Y10,1,3% &&?? Duplex selection example, PCLDuplex selection example, XES ??% %Y19,2% %Y96,nn% &&??Xdpm ISO Xdpm Ebcdic Xppm Ebcdic Xppm Ascii Output DataY70 Y36 Data Stream Translation Mode Function Settings Output??character Port Share OptionFunction 100 Port Share Option Y100 Y100,timeout,user string%Y100 = Example ??%%Y100,20,1B,45%%X1 Sending the commands from the systemPrinter sharing example Sending the commands from the PC??% %Y100,30,1B 45 1B 28 32 53% ??% %Y100,35,1BzlH%%X1Activating the Y249 Engineering Function Programming via ShareportDeactivating the Y249 Engineering Function Limitations when Y249 is activeUpdating firmware Escape sequences must be in HEXPC Support Virtual Printer Recoverable Errors Error MessagesMultistrike String is TOO Long Code Error Type Code Description Non-Recoverable Hardware ErrorsDescription Appendix a Supported Setup FunctionsXES Mode No. Description ESC Transparency FeaturesPCL Mode ESC Features Quick Reference Guideto the Supported FSL Functions Default depends N1 Physical paper Name Syntax Parameters Ly write PCL String Translate Table Ebcdic Name Syntax Parameters IBM Gfid APO Name Syntax Parameters Deviation Nvram Appendix B Test Printout 101 Appendix C Use of Xerox FS 5250 Serial Port Out IPDS, Programmer’s Guide Document no. D60253 Appendix D Related ManualsLaser 5250, Programmers Guide Document no. D62081 Lead-in/lead-out sequences Index