Xerox FS 5250 Selecting Fonts PCL, System /36 OCL Text -YES, Y98 Disabled, What to consider

Page 48

Selected FSL Functions

Xerox FS 5250, User’s Guide

If there is no STO command, no valid page size specified for Function Y98: Automatic Page Orientation, and the selected tray is set to COR, portrait orientation can be selected by setting the following parameters:

System /38 CL: PRTQLTY (*STD) or (*NLQ)

PAGRITT

System /36 OCL: TEXT -YES

ROTATE-0

Y98 Disabled

If function Y98 is disabled or if the logical page is wider and longer than the physical page (i.e. page not valid), then function Y10 will determine the page orientation. The interface will then use the default orientation as specified in Y10. The orientation may be in landscape, portrait or in COR. If you select COR and the system's print quality is not set to draft, then printing will be made in portrait.

11.5. Fonts

This section will provide the user with details on font selection and definition in PCL and XES mode.

11.5.1 Selecting Fonts - PCL

NOTE:

The procedures in this chapter can only be used, if you havelectedse the PCL option on the interface.

The Xerox FS 5250 emulates the IBM 5219 or 3812 printers. The fonts of these printers are different from the fonts 5 of a Xerox printer. You can install more fonts either as soft fonts or as font cassettes in the printer.

Many software programs will provide you with the facility of changing fonts. But if your software does not have this facility, you can still change fonts in a document by sending FSL commands to the interface.

What to consider

When you send a font change command to the interface, you must remember the following:

5See the basic printer manuals for an explanation of fonts.

- 48 -

Image 48

Contents EMC directive TrademarksSafety Notice Table of Contents PCL PC Support Virtual Printer Error Messages Appendix a Supported Setup FunctionsProgramming via Shareport What is the Xerox FS 5250? Introduction to the Xerox FSPrinter Driver Selection XES mode selection handles Xdpm and Xppm data streams IPC Upgrade Kit Items SuppliedProduct Features Non-IPCIf equipped with the optional IPC module Supported Control Units Installation Requirements Pre-Installation RequirementsNational Language Via the LineEU or US Settings Working EnvironmentConnections and Installation of the Xerox FS Rear Panel= PCL, B = XES Twinax Connector Emulation Changing the DriverVia the Line Selecting emulation via the line can be done inPCL onlyVia the Address Switch %Y37,5224%Non-IPDS Y37,n1 Write Emulation Y37,n1 Write EmulationCurrent emulation is Non-IPDS Selection EmulationSelection Emulation Address Setting Via the address switchDual Printer Emulation PCL only Non-IPDS as primary emulation Ipds as primary emulationUpgrading to Ipds Connecting the Xerox FS 5250to the Printer Connecting via Centronics outputConnecting the Xerox FS 5250to the System What if the CU Indicator fails to turn on?Test via the address switch Test FunctionTimeout Operation of the Xerox FS Top Panel of the Xerox FS1 CU PAR Parallel inputSER Serial input/output Ready Printer ReadyState Indication Function Selection via the Line Syntax of an FSL FunctionYfunction number,parameters% Escape Character Defining a Temporary Escape Character Removing Temporary Escape Character??% ??blankDefining a Permanent Escape Character Removing Permanent Escape CharacterY48,00 ??% Commands for Storing and Restoring Settings Command Description Example??% %X1 ??% %X3Pass-Through Mode PCL only%1B %%1B%Pass-through mode XES Transparency Mode Limitations For details refer to the programmers guide, doc. D62081IdaSetup Ipds Programming Programming the Xerox FS 5250 Non-IPDS Selected FSL Functions Paper SizeTrays Changing paper size??% %Y12,n1,n2% &&??space Value Paper SizeValue Paper Tray Saving the command Other commandsThis command also erases the escape character Changing paper size examplePaper Trays Basic printer set-upChanging paper trays Value n1 Format Characteristics FormatFormats Function Y10 Page FormatChanging Page Format ??% %Y10,n1,n2% &&??spaceValue n2 Tray Changing page format example ??% %Y10,2,3% %X1Automatic Page Orientation Function Y98 Automatic Page OrientationY98 Syntax Y98,n1,n2% Example Y98, 0,3%Automatic Page Orientation Chart Automatic Page OrientationExplanation to the chart on Automatic Page Orientation Y98 Enabled factory defaultY98 Disabled FontsSelecting Fonts PCL System /36 OCL Text -YESChanging font ??% %Y96,n1% &&??spaceDefault Gfid Table Symbol SET and TranslateGfid Scaleable Fonts Only applies to printers running PCL LevelTypeface ID PCL No Name of Typeface Style Strokeweight Defining Fonts PCLSymbol set of the font Value Symbol setWhat you need to know This is Helvetica Proportional spacing, boldItalic Selected FSL Functions Xerox FS 5250, User’s Guide Typeface of the font Value Typeface ValueTypefaceOther commands Selecting Fonts XESFont definition example ??% %Y91,521,6,5,1,18,1% %X1This function cannot be saved in the permanent memory Changing font example??% %Y96,41% &&?? Defining Fonts XES Font definitionXES Gfid Font strings sent OrientationGfid Gfid Optional Scaling CPI / Gfid RelationCOR CPI / Gfid Relation Font definition example Duplex Printing System or interface?What to consider Binding option ??% X4 &&????% Y19,0% &&?? Setting Description You cannot save the duplex command in the permanent memorySelecting duplex printing OrientationDuplex selection example, PCL ??% %Y19,2% %Y10,1,3% &&??Duplex selection example, XES ??% %Y19,2% %Y96,nn% &&??Output Data Xdpm ISO Xdpm Ebcdic Xppm Ebcdic Xppm AsciiData Stream Translation Mode Function Settings Output Y70 Y36Port Share Option Function 100 Port Share Option??character Y100,timeout,user string% Y100 =Y100 Sending the commands from the system Example ??%%Y100,20,1B,45%%X1Sending the commands from the PC Printer sharing example??% %Y100,30,1B 45 1B 28 32 53% ??% %Y100,35,1BzlH%%X1Programming via Shareport Activating the Y249 Engineering FunctionLimitations when Y249 is active Deactivating the Y249 Engineering FunctionUpdating firmware Escape sequences must be in HEXPC Support Virtual Printer Error Messages Recoverable ErrorsMultistrike String is TOO Long Non-Recoverable Hardware Errors Code Error Type Code DescriptionAppendix a Supported Setup Functions XES ModeDescription ESC Transparency Features No. DescriptionPCL Mode ESC Features Quick Reference Guideto the Supported FSL Functions Default depends N1 Physical paper Name Syntax Parameters Ly write PCL String Translate Table Ebcdic Name Syntax Parameters IBM Gfid APO Name Syntax Parameters Deviation Nvram Appendix B Test Printout 101 Appendix C Use of Xerox FS 5250 Serial Port Out Appendix D Related Manuals Laser 5250, Programmers Guide Document no. D62081IPDS, Programmer’s Guide Document no. D60253 Index Lead-in/lead-out sequences