Xerox FS 5250 IPC instruction manual Transparency Mode Limitations

Page 35

Function Selection via the Line

Xerox FS 5250, User’s Guide

NOTE:

When this pass-through option (with the lead-in/lead-out sequences) i used, it should be noted that apostrophe notation cannot apply. Only EBCDIC characters 0-9, A-F, a-f and spaces are accepted after a lead-in sequence. Control codes are suppressed. Other characters will terminate pass-through mode.

3.Filtered pass-through

To enter filter mode in XES, a lead-in and a lead-out string defined in function Y48 must be used:

Filter mode:

<start string>-<stop string>

This setting makes any text and IBM commands other than hex transparent data to be suppressed.

Normal mode

<start string>+<stop string>

This settings enables normal handling of text and IBM commands outside hex transparent data.

For details refer to the programmers guide, doc. D62081.

8.9. Transparency Mode Limitations

XES

The supported FSL functions of Xerox FS 5250 are accepted in all modes, but they have limited influence on the formatting in the various modes (Y70 and Y36).

For details on the FSL functions' influence on the formatting, you are referred to the Programmer's Guide, doc. no. D62081.

- 35 -

Image 35

Contents Trademarks EMC directiveSafety Notice Table of Contents PCL Programming via Shareport PC Support Virtual Printer Error MessagesAppendix a Supported Setup Functions Printer Driver Selection What is the Xerox FS 5250?Introduction to the Xerox FS XES mode selection handles Xdpm and Xppm data streams Items Supplied IPC Upgrade KitIf equipped with the optional IPC module Product FeaturesNon-IPC Supported Control Units Via the Line Installation RequirementsPre-Installation Requirements National LanguageWorking Environment EU or US Settings= PCL, B = XES Connections and Installation of the Xerox FSRear Panel Twinax Connector Selecting emulation via the line can be done inPCL only EmulationChanging the Driver Via the LineY37,n1 Write Emulation Via the Address Switch%Y37,5224% Non-IPDS Y37,n1 Write EmulationSelection Emulation Current emulation isNon-IPDS Selection Emulation Dual Printer Emulation PCL only Address SettingVia the address switch Ipds as primary emulation Non-IPDS as primary emulationUpgrading to Ipds Connecting via Centronics output Connecting the Xerox FS 5250to the PrinterWhat if the CU Indicator fails to turn on? Connecting the Xerox FS 5250to the SystemTest Function Test via the address switchTimeout PAR Parallel input Operation of the Xerox FSTop Panel of the Xerox FS 1 CUState Indication SER Serial input/outputReady Printer Ready Yfunction number,parameters% Function Selection via the LineSyntax of an FSL Function Escape Character ??blank Defining a Temporary Escape CharacterRemoving Temporary Escape Character ??%Removing Permanent Escape Character Defining a Permanent Escape CharacterY48,00 ??% ??% %X3 Commands for Storing and Restoring SettingsCommand Description Example ??% %X1%%1B% Pass-Through ModePCL only %1BPass-through mode XES For details refer to the programmers guide, doc. D62081 Transparency Mode LimitationsIdaSetup Ipds Programming Programming the Xerox FS 5250 Non-IPDS Changing paper size Selected FSL FunctionsPaper Size TraysValue Paper Tray ??% %Y12,n1,n2% &&??spaceValue Paper Size Changing paper size example Saving the commandOther commands This command also erases the escape characterChanging paper trays Paper TraysBasic printer set-up Function Y10 Page Format Value n1 Format CharacteristicsFormat FormatsValue n2 Tray Changing Page Format??% %Y10,n1,n2% &&??space ??% %Y10,2,3% %X1 Changing page format exampleExample Y98, 0,3% Automatic Page OrientationFunction Y98 Automatic Page Orientation Y98 Syntax Y98,n1,n2%Automatic Page Orientation Automatic Page Orientation ChartY98 Enabled factory default Explanation to the chart on Automatic Page OrientationSystem /36 OCL Text -YES Y98 DisabledFonts Selecting Fonts PCL??% %Y96,n1% &&??space Changing fontSymbol SET and Translate Default Gfid TableGfid Typeface ID PCL No Name of Typeface Scaleable FontsOnly applies to printers running PCL Level Defining Fonts PCL Style StrokeweightWhat you need to know Symbol set of the fontValue Symbol set Italic This is HelveticaProportional spacing, bold Selected FSL Functions Xerox FS 5250, User’s Guide ValueTypeface Typeface of the font Value Typeface??% %Y91,521,6,5,1,18,1% %X1 Other commandsSelecting Fonts XES Font definition example??% %Y96,41% &&?? This function cannot be saved in the permanent memoryChanging font example Font definition Defining Fonts XESFont strings sent Orientation XES GfidGfid Gfid COR CPI / Gfid Relation Optional ScalingCPI / Gfid Relation Font definition example What to consider Duplex PrintingSystem or interface? ??% Y19,0% &&?? Binding option??% X4 &&?? Orientation Setting DescriptionYou cannot save the duplex command in the permanent memory Selecting duplex printing??% %Y19,2% %Y96,nn% &&?? Duplex selection example, PCL??% %Y19,2% %Y10,1,3% &&?? Duplex selection example, XESXdpm ISO Xdpm Ebcdic Xppm Ebcdic Xppm Ascii Output DataY70 Y36 Data Stream Translation Mode Function Settings Output??character Port Share OptionFunction 100 Port Share Option Y100 Y100,timeout,user string%Y100 = Example ??%%Y100,20,1B,45%%X1 Sending the commands from the system??% %Y100,35,1BzlH%%X1 Sending the commands from the PCPrinter sharing example ??% %Y100,30,1B 45 1B 28 32 53%Activating the Y249 Engineering Function Programming via ShareportEscape sequences must be in HEX Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating firmwarePC Support Virtual Printer Recoverable Errors Error MessagesMultistrike String is TOO Long Code Error Type Code Description Non-Recoverable Hardware ErrorsDescription Appendix a Supported Setup FunctionsXES Mode No. Description ESC Transparency FeaturesPCL Mode ESC Features Quick Reference Guideto the Supported FSL Functions Default depends N1 Physical paper Name Syntax Parameters Ly write PCL String Translate Table Ebcdic Name Syntax Parameters IBM Gfid APO Name Syntax Parameters Deviation Nvram Appendix B Test Printout 101 Appendix C Use of Xerox FS 5250 Serial Port Out IPDS, Programmer’s Guide Document no. D60253 Appendix D Related ManualsLaser 5250, Programmers Guide Document no. D62081 Lead-in/lead-out sequences Index