Xerox FS 5250 IPC This function cannot be saved in the permanent memory, Changing font example

Page 59

Selected FSL Functions

Xerox FS 5250, User’s Guide

2.If you only send a font change without also changing Lines Per Inch and/or Characters Per Inch, you could have format problems.

Changing font

The font change command has one parameter, the GFID value . You can change the contents of this parameter, if you wish to use a font that is not in the list. See the next chapter on how to define a font. You send the font change command as follows:

&&??% %Y96,<n1>% &&??<space>

The command &&??% selects the character "%" as the escape character. The escape character is a signal to the interface that the data stream following is a command stream. The last command in the above line (&&?? <space>) erases the temporary escape character again.

NOTE:

This function cannot be saved in the permanent memory.

Changing font example

&&??% %Y96,41% &&??

This will select the font defined as number GFID 41. It will also erase the escape character.

Other commands

The other command that can be used in connection with font selection, is:

FSL Y97, Font Definition (User-defined)

- 59 -

Image 59

Contents Trademarks EMC directiveSafety Notice Table of Contents PCL Programming via Shareport PC Support Virtual Printer Error MessagesAppendix a Supported Setup Functions Printer Driver Selection What is the Xerox FS 5250?Introduction to the Xerox FS XES mode selection handles Xdpm and Xppm data streams Items Supplied IPC Upgrade KitIf equipped with the optional IPC module Product FeaturesNon-IPC Supported Control Units Via the Line Installation RequirementsPre-Installation Requirements National LanguageWorking Environment EU or US Settings= PCL, B = XES Connections and Installation of the Xerox FSRear Panel Twinax Connector Selecting emulation via the line can be done inPCL only EmulationChanging the Driver Via the LineY37,n1 Write Emulation Via the Address Switch%Y37,5224% Non-IPDS Y37,n1 Write EmulationSelection Emulation Current emulation isNon-IPDS Selection Emulation Dual Printer Emulation PCL only Address SettingVia the address switch Ipds as primary emulation Non-IPDS as primary emulationUpgrading to Ipds Connecting via Centronics output Connecting the Xerox FS 5250to the PrinterWhat if the CU Indicator fails to turn on? Connecting the Xerox FS 5250to the SystemTest Function Test via the address switchTimeout PAR Parallel input Operation of the Xerox FSTop Panel of the Xerox FS 1 CUState Indication SER Serial input/outputReady Printer Ready Yfunction number,parameters% Function Selection via the LineSyntax of an FSL Function Escape Character ??blank Defining a Temporary Escape CharacterRemoving Temporary Escape Character ??%Removing Permanent Escape Character Defining a Permanent Escape CharacterY48,00 ??% ??% %X3 Commands for Storing and Restoring SettingsCommand Description Example ??% %X1%%1B% Pass-Through ModePCL only %1BPass-through mode XES For details refer to the programmers guide, doc. D62081 Transparency Mode LimitationsIdaSetup Ipds Programming Programming the Xerox FS 5250 Non-IPDS Changing paper size Selected FSL FunctionsPaper Size TraysValue Paper Tray ??% %Y12,n1,n2% &&??spaceValue Paper Size Changing paper size example Saving the commandOther commands This command also erases the escape characterChanging paper trays Paper TraysBasic printer set-up Function Y10 Page Format Value n1 Format CharacteristicsFormat FormatsValue n2 Tray Changing Page Format??% %Y10,n1,n2% &&??space ??% %Y10,2,3% %X1 Changing page format exampleExample Y98, 0,3% Automatic Page OrientationFunction Y98 Automatic Page Orientation Y98 Syntax Y98,n1,n2%Automatic Page Orientation Automatic Page Orientation ChartY98 Enabled factory default Explanation to the chart on Automatic Page OrientationSystem /36 OCL Text -YES Y98 DisabledFonts Selecting Fonts PCL??% %Y96,n1% &&??space Changing fontSymbol SET and Translate Default Gfid TableGfid Typeface ID PCL No Name of Typeface Scaleable FontsOnly applies to printers running PCL Level Defining Fonts PCL Style StrokeweightWhat you need to know Symbol set of the fontValue Symbol set Italic This is HelveticaProportional spacing, bold Selected FSL Functions Xerox FS 5250, User’s Guide ValueTypeface Typeface of the font Value Typeface??% %Y91,521,6,5,1,18,1% %X1 Other commandsSelecting Fonts XES Font definition example??% %Y96,41% &&?? This function cannot be saved in the permanent memoryChanging font example Font definition Defining Fonts XESFont strings sent Orientation XES GfidGfid Gfid COR CPI / Gfid Relation Optional ScalingCPI / Gfid Relation Font definition example What to consider Duplex PrintingSystem or interface? ??% Y19,0% &&?? Binding option??% X4 &&?? Orientation Setting DescriptionYou cannot save the duplex command in the permanent memory Selecting duplex printing??% %Y19,2% %Y96,nn% &&?? Duplex selection example, PCL??% %Y19,2% %Y10,1,3% &&?? Duplex selection example, XESXdpm ISO Xdpm Ebcdic Xppm Ebcdic Xppm Ascii Output DataY70 Y36 Data Stream Translation Mode Function Settings Output??character Port Share OptionFunction 100 Port Share Option Y100 Y100,timeout,user string%Y100 = Example ??%%Y100,20,1B,45%%X1 Sending the commands from the system??% %Y100,35,1BzlH%%X1 Sending the commands from the PCPrinter sharing example ??% %Y100,30,1B 45 1B 28 32 53%Activating the Y249 Engineering Function Programming via ShareportEscape sequences must be in HEX Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating firmwarePC Support Virtual Printer Recoverable Errors Error MessagesMultistrike String is TOO Long Code Error Type Code Description Non-Recoverable Hardware ErrorsDescription Appendix a Supported Setup FunctionsXES Mode No. Description ESC Transparency FeaturesPCL Mode ESC Features Quick Reference Guideto the Supported FSL Functions Default depends N1 Physical paper Name Syntax Parameters Ly write PCL String Translate Table Ebcdic Name Syntax Parameters IBM Gfid APO Name Syntax Parameters Deviation Nvram Appendix B Test Printout 101 Appendix C Use of Xerox FS 5250 Serial Port Out IPDS, Programmer’s Guide Document no. D60253 Appendix D Related ManualsLaser 5250, Programmers Guide Document no. D62081 Lead-in/lead-out sequences Index