Xerox 144, 120 Output, Tabs, Stapling, Additional notes related to DocuPrint migration

Page 47

Xerox Nuvera® 100/120/144 EA Digital Production System - Customer Expectations Document

Output

Paper sizes supported to the main tray (stapled and unstapled): Process direction - 7.0 to 18.5 in. (178 mm to 470 mm) Cross Process direction - 8.0 to 12 in. (203 mm to 305 mm)

Smaller sizes (down to A5 and Statement) or larger sizes (including SRA3) can be run to the top tray.

Mixed sized output allows stacking of different size pages, both in the process and cross-process direction, in a single job.

When stapling sets with mixed size stock, the stock must be the same dimension in the Across Feed direction, and the dimension differences should be within 13mm (½”) in the feed direction.

To have the BFM staple correctly, the output must be 1-N facedown.

Envelopes can only be sent open flap trailing to the Top Tray, and should be limited to 15, or mis- stacking may occur.

The BFM / BFM Plus does not offset paper sizes larger than 11”x17" / A3. This means that 12”x18” or 12x18.5” cannot be offset. For these sizes, the software ignores any offset programming selection, and runs without offsetting.

Banner and slip sheets should be greater than or equal to 90 gsm (24 lb bond)

Slip-sheets must be the same size as the body sheets

Stapler capacity is reduced for coated papers and paper heavier than 20 lb. bond (75 gsm).

For reliable stacking, stack size should be limited for certain jobs:

--Offset single sheet jobs should be limited to 100 sheets. (20 lb bond or 75 gsm) --Stapled sets of 15 sheets or smaller are limited by machine control to 100 sets.

--Stapled sets of coated stocks stack less well, and should be managed to 50 by the operator. --Stapled sets should be offset stacked.

--The stack height limitation can be operator adjusted.

Automatic bin limits control the number of sheets collected and compiled in the finisher when running unfinished sets to optimize the set drop performance and improve job recovery.

Tabs

The tabs cross process length must be the same as the body of the document. The tab can be no longer than 0.5” (13mm) in the process direction beyond the body of the document. Tabs sized for use with 8.5” x 11” and A4 stock, long edge feed, are supported

Transparencies

Transparencies run to the stacker must have a slip-sheet between each one.

Stapling

The BFM is delivered with a 5000 staple cartridge of 100-sheet staples installed in each of the two staplers.

Staples for up to 30 sheets and for up to 100 sheets are available. Stapled jobs over 100 sheets are inhibited. The machine does not detect staple size. The operator must manage jobs to be within capability of the loaded staple size.

Some marking of the staple onto an adjacent set may be seen.

Not all stapler failure modes are detected by the machine logic. The customer may find some

occurrence of unstapled sets in the output.

Carbonless

In the DPS BFM configuration, curl that faces up poses more of a problem than curl that faces down. To avoid up curl, 2, 3 and 4 part Carbonless should be run to the BFM in an N to1 mode and use reverse collated versions of the recommended Xerox media. See compatible media tables in this document.

Additional notes related to DocuPrint migration

The BFM is a set-level device. It is designed to collect sheets into set-sized chunks (using the compiling station), optionally staple and/or offset the chunks, and then place those on to the stack below. It can reliably stack unfinished output, and it supports unloading and auto-switching to another available BFM Stacker; however, the following should be noted:

Since it is a set-level device, boundaries between chunks in a stack may be visible.

- 47 -

Image 47
Contents Xerox Nuvera 100/120/144 EA Digital Production System BFM BFM Table of Contents Bourg Bdfx Booklet Maker with Optional Bcfx Covers Feeder Envelopes IntroductionProduct Overview Crucial Performance ExpectationsDocuCards FreeFlowDocuSPPrinter Module Multifunction Finisher FreeFlowTM Digital Workflow CollectionNew Capabilities with Xerox Nuvera System Release With individual Output / Finishing Devices System Media Capability- Xerox NuveraSquarefold Conditions Print Volume RangeSystem AmpvMaximum Environmental FactorsEnvironmental Factor Minimum Product Space & Power Requirements Availability System Configuration and InstallationInstallation Preparation Document System InstallationConsumables OperationsSupplies and Component Yields Kit Limitations PrInteract formerly Remote ServicesXerox Productivity Plus XPP Compatible Media List Remove frequently from 3R11602 3R11603 3R11063 Green 3R12065 DuraPaper 10mil 163gsm 3R11542 3R11543 Connectivity Product Specifications Overview by Sub-SystemFreeFlowTM Makeready, Web Services Process Manager Labels Vipp Variable Data Intelligent PostScript PrintwareFreeFlow Print Manager / IPP Network ConnectivityScanner Module Scan to Digital Digital Front End DFE FreeFlow DocuSP Key features of FreeFlow DocuSP includeCopy Jobs Productivity Impacts Print From Digital FileScan to Digital File Saving jobsLcds Print Description Language Lcds and IpdsIpds Print Description Language Comments Sheet Feed ModulesSFM LfsfmSpecial Stocks Input Sizes Inserter Module IMInsertion Module used with Comments Multifunction Finisher Engine speed per paper size impressions per minute Printer ModuleImage Quality Expectations Xerographic Color Prints Printer Module CapabilitiesPrint to Edge SRA3 PrintingProfessional Finisher Sub-system Feature CommentsMultifunction Finisher Professional and Pro Plus Hole Punch Pro Plus FinisherInsertion Tray Within Set Registration MFF Professional MFF Pro PlusStack Quality See Figure Stapled Sets Within Set Specifications See Figure Unstapled Sets Within Set SpecificationsOutput to Main Stacker Double Staple Output to Top TrayOutput to Main Stacker Unstapled Output to Main Stacker Single stapleOutput to Fold Tray C Fold, Z Fold, Bi-Fold BFM Basic Finishing Module BFM and BFM PlusAdditional notes related to DocuPrint migration OutputTabs StaplingMedia Size Table Media Size Table contd BFM / BFM Plus System Standard Paper SizesSimplex to simplex duplex to duplex Sound Emission Dimensions Finishing Transport Module FTMFinishing Transport Module FTM Media Latitude Finishing Transport Module FTM CapacityMedia Latitude DS5000 Dimensions DS5000Xerox DS5000 High Capacity Stacker Electrical DS5000 Environmental Minimum MaximumPage Device North America Europe Dimensions Bourg BDFx Bourg BCFxSqedg Stapling / Folding Specifications Media Latitude Squarefold Booklet Maker Sqfbm Dimensions Squarefold Booklet MakerXerox SquareFold BookletMaker Sqfbm SqfbmElectrical & Environmental GBC Fusion Punch Minimum Maximum Dimensions GBC Fusion Punch Bypass Stacker Offset StackerGBC Fusion Punch II with Offset Stacker Media Latitude GBC Fusion Punch Media Latitude Xerox DB120-D Document Binder Dimensions Xerox DB120-D Document BinderXerox DB120-D Document Binder Xerox Manual and Book Factory BBF2005 Input Unit Dimensions BBF2005Dimensions CMT-330 Cooling Tower Conveyors BprfBook Sizes Stock WeightMedia Latitude BBF2005 with Bprf BBF2205 without Bprf RangeXerographic printer Post-process Uses of Xerox Nuvera OutputPermanence Overprint
Related manuals
Manual 34 pages 6.29 Kb