Xerox Nuvera® 100/120/144 EA Digital Production System - Customer Expectations Document
Basic Finishing Module (BFM) and BFM Plus
| Dimensions | Basic Finishing Module (BFM) |
|
| Width X Depth X Height | 32.9” X 28” X 44.5” (835.7mm X 711.2mm X 1130.3mm) |
|
| Weight | 369 lbs. ( 167.4 kg) |
|
| Clearance: Operator | Minimum 38” in front of module |
|
| Clearance: Service | Minimum 30” from back wall |
|
|
|
|
|
|
| Dimensions |
|
|
| Basic Finishing Module Plus (BFM Plus) |
|
| |||
|
| Width X Depth X Height |
|
|
| 48” X 28” X 44.5” (1220mm X 711.2mm X 1130.3mm) |
| BFM | |||
|
| Weight |
|
|
| 494 lbs. ( 167.4 kg) |
|
| |||
|
|
|
|
|
|
|
| ||||
|
| Clearance: Operator |
|
|
| Minimum 38” in front of module |
|
| |||
|
| Clearance: Service |
|
|
| Minimum 30” from back wall |
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
| Electrical & |
|
|
|
| BFM / BFM Plus |
|
| ||
|
| Environmental |
|
|
|
| Minimum |
| Maximum |
|
|
|
| Temperature Range |
|
|
| 50° F (10° C) |
| 90° F (32.2° C) |
|
| |
|
| Humidity Range |
|
|
| 15% RH |
| 85% RH |
|
| |
|
| Altitude |
|
|
| 0 ft |
|
| 10,000 ft. (3048m) |
|
|
|
| Power |
|
|
| 200 - 240 VAC ± 10%, 50/ | 60 Hz, 8Amps |
| BFM Plus | ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
| Media Latitude |
|
|
|
|
|
| BFM / BFM Plus |
| |
|
| Stock Weight Range |
|
|
| Uncoated: 16lb. bond to 120lb. index (56 to 250 gsm) |
| ||||
|
|
|
|
| Coated: (90 to 250gsm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
| Stock Size Range |
|
|
| 7” x 8” to 12” x 18.5” (178 x 203mm to 320mm x 470mm) – See table on following pages | |||||
|
| Top Tray Capacity |
|
| 250 | (20 lb. bond / 75 gsm) |
|
|
| ||
|
| Main Stacker |
|
| 3000 | (20 lb. bond / 75 gsm) |
|
|
| ||
|
| Stapler |
|
|
| One or two staples, up to 100 sheets (20 lb. bond / 75 gsm) |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
System Compatibility
There are two models: the BFM has a top tray (also know as purge tray); the BFM Plus includes a bypass transport over the stacker
Both the BFM and the BFM Plus may be installed to enable continuous running with
1 or 2 BFM Plus’es may be installed to connect to a downstream FTM to add supported inline DFA finishing.
BFM / BFM Plus Operation
Continuous operation with unload while run is fully supported with a BFM and BFM Plus installation. When a stacker is full or not ready (e.g. out of staples) the system can auto switch to another available stacker. Unloads can be configured to occur automatically at stacker limit, at job boundaries, at set or
partition boundaries, or can be initiated manually via the Stacker Unload button or the GUI. A stacker's limit can be configured to any value between 200 and 3000 and each BFM stacker can be configured independently and differently. If desired, operators can also program jobs to specific stacker destinations.
Bypass via BFM Plus
Bypass to a downstream finishing device is a capability of the BFM Plus
- 46 -