Belkin F6C110-RKM-2U Faqs, Maintenance, Battery Replacement, Symptom Possible Cause What To Do

Page 13

FAQS

 

 

 

 

 

 

Symptom

Possible Cause

What To Do

 

 

 

 

 

 

 

UPS will not turn on

On/Off/Test button not pushed

Press the On button

 

 

 

 

momentarily (one beep to

 

 

 

 

start UPS)

 

 

 

 

 

 

 

UPS operates in battery mode

Input AC circuit breaker is

Reset circuit breaker by

 

 

only, even though there is

tripped

pressing the plunger back in.

 

 

normal AC present

 

If the AC circuit breaker trips

 

 

 

 

after UPS starts up, reduce the

 

 

 

 

load on the UPS.

 

 

 

 

 

 

 

The UPS emits a sustained tone

UPS has detected an internal

Call for service

 

 

 

fault

 

 

 

 

 

 

 

 

The Site Wiring Fault LED is

Incorrect service wiring

Have a qualified electrician

 

 

illuminated

 

correct the service wiring

 

 

 

 

 

 

 

The Battery On LED is

The UPS is being controlled via

Disconnect the computer cable

 

 

illuminated, but there

its computer port.

from the UPS and press the On

 

 

is no output

 

button momentarily. If UPS

 

 

 

 

works normally, software has

 

 

 

 

control of the UPS.

 

 

 

 

 

 

 

UPS does not provide expected

The batteries may be weak or

Charge the batteries for 8 hours

 

 

backup time with internal

at the end of useful service life.

and retest. If the backup time

 

 

batteries or with a battery pack

The battery pack’s circuit

is still less than expected, the

 

 

 

breaker may be tripped.

batteries may need to be

 

 

 

 

replaced, even though the

 

 

 

 

Weak/Bad Battery LED is not

 

 

 

 

illuminated. Reset the battery

 

 

 

 

pack’s circuit breaker.

 

 

 

 

 

 

 

Replace Battery LED is

Weak or bad batteries/bad

Check battery connection/

 

 

illuminated

battery connection

replace batteries. Follow battery

 

 

 

 

replacement procedures in

 

 

 

 

section 6.

 

 

 

 

 

 

 

UPS occasionally emits a beep

Normal operation

The UPS is performing its

 

 

 

 

intended function.

 

 

 

 

 

 

 

Overload LED is illuminated and

The load has exceeded the UPS’

Check the specifications (see

 

 

a constant alarm sounds

capacity

section 8). Remove part of the

 

 

 

 

load.

 

 

 

 

 

 

 

The Battery On LED is blinking

The UPS is in either the Buck

The UPS is performing its

 

 

and the audible alarm is silent

mode or the Boost mode

intended function.

 

 

 

 

 

 

 

 

 

 

 

MAINTENANCE

Battery Replacement

The OmniGuard Rackmount series has easy-to-replace hot-swappable batteries. Please read the following warning statements before attempting to service the battery(s). NOTE: If there is a power interruption while replacing the hot- swappable batteries, with the UPS on, the load will not be backed up.

WARNING: This Uninterruptible Power Source contains potentially hazardous voltages. Do not attempt to disassemble the unit beyond battery replacement procedures below. Except for the battery, this UPS contains no user-serviceable parts. Repairs should be performed by service personnel only

CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION: Although battery system voltages are only 24VDC and 48VDC, the battery system can still present a risk of electrical shock. The current capability of a battery is sufficient to burn wire or tools very rapidly, producing molten metal. Observe these precautions when replacing the batteries:

1.Remove watches, rings, or other metal objects.

2.Use hand tools with insulated handles.

3.Do not lay tools or other metal parts on top of batteries.

CAUTION: Replace batteries with the same number and type as originally installed in the UPS. These batteries have pressure- operated vents.

 

Series Model #

Battery Model #

 

 

 

 

 

 

 

F6C110-RKM-2U

12V

7.2Ah

 

 

 

 

 

 

 

F6C150-RKM-2U

12V

4.5Ah

 

 

 

 

 

 

 

F6C230-RKM-2U

12V

9Ah

 

 

 

 

 

 

 

F6C320-RKM-3U

12V

12Ah

 

 

 

 

 

 

24

25

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Belkin OmniGuard Rackmount UPS Introduction Table of ContentsPage Highlights OverviewPackage Contents Quick Start Product InstallationCharging the Battery Connecting to an AC Power SourceMounting the UPS within the Rack Attaching the Brackets to the UPSConnecting your Equipment Product DiagnosticsTurning the Unit On/Off DIP Switch SettingsSelf-Test Communications Port AlarmsDB9 Standard Pin-Out Pin 2 /TXD Pin 3 /RXDCommunications Port Connection Software Features & InstallationSelect the UPS page, and then click on Select… Maintenance FaqsBattery Replacement Symptom Possible Cause What To DoBattery Replacement Instructions Obtaining ServiceOmniGuard TM Rackmount UPS Specifications 120VAC models Technical SpecificationsPage P74264

F6C110-RKM-2U specifications

The Belkin F6C110-RKM-2U is a versatile and efficient power management solution designed to meet the growing demands of modern electronic devices. This 10-outlet power strip is not only a reliable source of power but also integrates advanced technologies to enhance safety, reduce energy consumption, and provide excellent surge protection.

One of the main features of the Belkin F6C110-RKM-2U is its robust surge protection. Equipped with a 3940 Joule surge protection rating, this power strip is capable of safeguarding your valuable devices from voltage spikes and surges caused by lightning strikes or electrical fluctuations. This makes it an ideal choice for home offices, entertainment setups, and any other electronic environments where sensitive equipment is utilized.

In addition to surge protection, the F6C110-RKM-2U also offers EMI/RFI filtering, which helps to minimize electromagnetic interference and radio frequency interference. This technology ensures that your devices operate seamlessly without any disruptions caused by electrical noise, which is particularly important for audio and video equipment.

Another notable characteristic of this power strip is its space-saving design. The F6C110-RKM-2U features a compact and slim profile that allows for easy placement in tight spaces, whether it be behind a desk or on a wall-mounted shelf. Its flat plug design facilitates close placement to walls or furniture, reducing the risk of tangles and mess.

The power strip also incorporates an energy-efficient solution with its intelligent circuitry, which monitors and distributes power to devices connected to it. This not only extends the lifespan of your electronics but also contributes to energy savings in households and offices.

For added convenience, the Belkin F6C110-RKM-2U features a 6-foot long power cord, providing flexibility in placement and reducing the need for additional extension cords. Additionally, the power strip is equipped with a signature green LED indicator, which illuminates to indicate that the surge protection is active.

Overall, the Belkin F6C110-RKM-2U is a reliable power management tool that combines safety, convenience, and efficiency. Whether you are protecting your home theater system, office equipment, or gaming consoles, this power strip stands out as a practical solution for modern power needs.
Top Page Image Contents