Atlona AT-HD88M-SR manual SW1-SW8 for EDID/Audio

Page 9

￿￿'￿￿￿+￿￿￿￿￿

SW1-SW8 for EDID/Audio

 

DIP Switch Position

 

 

Video

 

 

Audio

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin#1

 

 

Pin#2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF [￿]

 

 

OFF [￿]

 

 

Up to 1080p

 

Stereo1

 

Default Mode2 – Up to 1080p & stereo audio output for most

 

 

 

 

 

 

 

 

 

 

 

 

 

HDTVs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF [￿]

 

 

ON [￿]

 

 

Up to

 

 

Stereo

 

Safe Mode3 Enforce the system output at 720p/1080i video

 

 

 

 

 

720p/1080i

 

 

and stereo audio for basic compatibility among HDTVs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON [￿]

 

 

OFF [￿]

 

 

Bypass

4

 

Bypass

 

EDID Learning Mode5 – for learning EDID from the display

 

 

 

 

 

 

4

 

 

while playing any received HDMI audio format

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON [￿]

 

 

ON [￿]

 

 

 

 

 

 

 

 

EDID Learning & Stereo Mode5 – for learning EDID from the

 

 

 

 

 

Bypass

 

Stereo

 

display while enforcing stereo output if any HDTV cannot play

 

 

 

 

 

 

 

 

 

 

 

 

 

surround sound normally

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

Note

1If the HDTV shows video but without audio, please try to set audio mode to stereo.

2Factory default setting of [SW1]-[SW8]is pin#1-OFF[￿] & pin#2- OFF[￿] for 1080p with stereo.

3If you encounter any unsolved audio/video output problem during system installation, please turn any [SW1]-[SW8]to pin#1-OFF[￿] & pin#2-ON[￿]for safe mode to enforce the most compatible

720p stereo output for system check. However, the safe mode cannot be initiated if your HDMI source is set to enforce 1080p output. In this case, please reconfigure your HDMI source to all resolution output for troubleshooting.

4Bypass means the matrix will maintain playing the original format of HDMI signals in video and perhaps audio. By setting at this mode, the users may encounter compatibility issue among different kinds of HDMI sources and displays. If you cannot get the audio and/or video output normally at the system installation, please change the DIP switch setting to default mode or even safe mode to verify the functionality of the device.

5To learn the EDID of HDMI display for respective HDMI source devices, please see the [EDID Learning] section in the next page for more detail information.

7

Image 9
Contents Page $! % Page Features AT-HD88M-SR Mode 1-8 Preset Profiles Mode Selection 1, 2, 3, 4, 5, 6, 7, 8, E, H, L, 1Mode E Edid Learning Mode Mode H Panel Hold and UnholdRear Panel of AT-HD88M-S Mode L System Lock and UnlockAT-HD88M-R SW1-SW8 for EDID/Audio SW Main for firmware update for technical support only IR Extenders IR SocketsIR Blaster IR Receiver Definition of IR Earphone Jack Supported IR Data FormatIR Blaster AT-HD88M-R as receiver unit AT-HD88M-S as master unitMethod B IR Remote Control Source SideMethod a Push-in Button Method a Push-in button for switching input channels Method B1 IR remote control for switching input channelsDisplay Side Scan button Method C Software Control through RS-232 serial portLinkage button Setting buttonOpen/Close button Mapping buttonGroup setting One by one settingBy using Terminal Command SetMethod a Manually connect Hdmi display to Hdmi Input Method B Using Front PanelCustom Code 01 EE 14-key IR remote default 01 EE Receiver Unit Master Unit 0x01 0xEECustom Code IR3 0x12 Custom Code 0x12 Custom Code IR4 0x13 Custom Code 0x13 Command Custom CodeSafeguards Limited Warranty