IBM 71455DU manual Do not

Page 10

Statement 2:

CAUTION:

When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not:

vThrow or immerse into water

vHeat to more than 100°C (212°F)

vRepair or disassemble

Dispose of the battery as required by local ordinances or regulations.

Statement 3:

CAUTION:

When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following:

vDo not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

vUse of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

DANGER

Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following.

Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

viiiIBM System x3950 Type 8878 and System x3950 E Type 8879: User’s Guide

Image 10
Contents User’s Guide Page User’s Guide Page Contents Page Safety Page To Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Page System x3950 and System x3950 E server Related documentationProblem Determination and Service Guide Features and specifications Features and specifications What your server offers Redundant cooling and power capabilities Light path diagnosticsPowerExecutive Redundant connection Integrated network supportReliability, availability, and serviceability UpdateXpress program IBM DirectorServer controls, connectors, LEDs, and power Front viewPage Rear view Server power features Turning on the server Turning off the serverPage Installing options Server componentsBoard internal connectors and jumpers Jumper name DescriptionMemory-card connectors Memory-card LEDsMicroprocessor-board connectors and LEDs PCI-X board connectors PCI-X board LEDsSAS-backplane connectors Installation guidelines Working inside the server with the power on System reliability guidelinesHandling static-sensitive devices Removing the cover and bezelInstalling a hot-swap power supply Locking latch Locking handle open Installing an adapter ServeRAID-8i adapter ServeRAID-8i slot LED Adapter guide Installing a hot-swap hard disk drive Installing options Memory module Memory card order Dimm pairActive Memory Select Memory Settings Select Memory Mirroring Settings Adding a memory card Adding and replacing a memory cardHot-replacing a memory card Installing DIMMs Installing a DimmDcac Hot-swapping DIMMs Installing options Hot-adding DIMMs Dimm Microprocessor Microprocessor installation order Installing a microprocessor Air baffle Heat sink Microprocessor connector Microprocessor- release lever Completing the installation Rear view Connecting the cablesFront view Two-node configuration Updating the server configurationSMP Expansion cabling Four-node configuration Protective cover Eight-node configuration Node SMP Expansion cable Page Installing options Page Gigabit Ethernet controller configuration process Configuration/Setup Utility programBoot Menu program SAS/SATA Configuration Utility programStarting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices System Card Data Power-on PasswordAdministrator Password Devices and I/O PortsRSA II Settings Advanced SetupMemory Settings System Partition VisibilityBMC Serial Port Access Mode Baseboard management controller BMC settingsBMC Post Watchdog Timeout Reboot system on NMIPasswords Power-on passwordUsing the ServerGuide Setup and Installation CD Administrator passwordServerGuide features Setup and configuration overviewUsing the Boot Menu program Typical operating-system installationInstalling your operating system without ServerGuide Download section, click Downloads & driversStarting the PXE boot agent utility program Configuring the Gigabit Ethernet controllerUsing the PXE boot agent utility program PXE boot agent utility menu choicesCommand-line interface Ipmi Shell Banner Message TimeoutPre-boot Wake on LAN Link SpeedUpdating and configuring the Bios Configuring Linux Configuring Red Hat Enterprise Linux ESOriginal /etc/lilo.conf contents Add the following five lines between the two title= sections Original /boot/grub/grub.conf contents Suse Sles 8.0 configuration Append the following text to the first title line Configuring a Microsoft Windows operating system Original bootcfg program outputInstalling the OSA SMBridge management utility program Modified bootcfg program outputUsing the baseboard management controller utility programs Using the OSA SMBridge management utility program Using ServeRAID Manager Using the SAS/SATA Configuration Utility programStarting the SAS/SATA Configuration Utility program SerialSelect Utility menu choicesUsing custom configuration Configuring the controllerUsing express configuration Click Express configurationUsing the Scalable Partition Web Interface Viewing the configurationCreating a scalable partition Page Configuring the server Page Deleting a scalable partition Page Updating IBM Director Page Appendix. Notices TrademarksImportant notes Product recycling and disposal Page Index LED SAS Memory-mirroring configuration Page Part Number 31R1871