IBM 71455DU manual Led

Page 40

If you have other options to install or remove, do so now; otherwise, go to “Completing the installation” on page 47.

Attention: Static electricity that is released to internal server components when the server is powered-on might cause the server to halt, which could result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when working inside the server with the power on.

To install a hot-plug PCI or PCI-X adapter, complete the following steps.

Note: For hot-pluggable adapters, make sure that the PCI hot-plug device driver is installed.

1.Read the safety information that begins on page v and “Installation guidelines” on page 21.

2.If the adapter is not hot-pluggable, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

3.Remove the server cover (see “Removing the cover and bezel” on page 23) and determine which PCI-X expansion slot you will use for the adapter.

 

Adapter

Attention Tab

retention

LED

latch

(yellow)

 

PCI-X retaining

PCI-X

Power

bar

LED

 

divider

(green)

DCAC

4.See the documentation that comes with the adapter for instructions for setting jumpers or switches and for cabling.

Note: Route adapter cables before you install the adapter.

5.Install the adapter:

a.Open the blue PCI-X retaining bar by lifting the front edge.

b.Push the orange adapter retention latch toward the rear of the server and open the tab. The power LED for the slot turns off.

28IBM System x3950 Type 8878 and System x3950 E Type 8879: User’s Guide

Image 40
Contents User’s Guide Page User’s Guide Page Contents Page Safety Page To Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Page System x3950 and System x3950 E server Related documentationProblem Determination and Service Guide Features and specifications Features and specifications What your server offers Light path diagnostics PowerExecutive Redundant connectionRedundant cooling and power capabilities Integrated network supportReliability, availability, and serviceability UpdateXpress program IBM DirectorServer controls, connectors, LEDs, and power Front viewPage Rear view Server power features Turning on the server Turning off the serverPage Installing options Server componentsBoard internal connectors and jumpers Jumper name DescriptionMemory-card connectors Memory-card LEDsMicroprocessor-board connectors and LEDs PCI-X board connectors PCI-X board LEDsSAS-backplane connectors Installation guidelines Working inside the server with the power on System reliability guidelinesHandling static-sensitive devices Removing the cover and bezelInstalling a hot-swap power supply Locking latch Locking handle open Installing an adapter ServeRAID-8i adapter ServeRAID-8i slot LED Adapter guide Installing a hot-swap hard disk drive Installing options Memory module Memory card order Dimm pairActive Memory Select Memory Settings Select Memory Mirroring Settings Adding a memory card Adding and replacing a memory cardHot-replacing a memory card Installing DIMMs Installing a DimmDcac Hot-swapping DIMMs Installing options Hot-adding DIMMs Dimm Microprocessor Microprocessor installation order Installing a microprocessor Air baffle Heat sink Microprocessor connector Microprocessor- release lever Completing the installation Rear view Connecting the cablesFront view Two-node configuration Updating the server configurationSMP Expansion cabling Four-node configuration Protective cover Eight-node configuration Node SMP Expansion cable Page Installing options Page Configuration/Setup Utility program Boot Menu programGigabit Ethernet controller configuration process SAS/SATA Configuration Utility programStarting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices Power-on Password Administrator PasswordSystem Card Data Devices and I/O PortsAdvanced Setup Memory SettingsRSA II Settings System Partition VisibilityBaseboard management controller BMC settings BMC Post Watchdog TimeoutBMC Serial Port Access Mode Reboot system on NMIPasswords Power-on passwordUsing the ServerGuide Setup and Installation CD Administrator passwordServerGuide features Setup and configuration overviewTypical operating-system installation Installing your operating system without ServerGuideUsing the Boot Menu program Download section, click Downloads & driversConfiguring the Gigabit Ethernet controller Using the PXE boot agent utility programStarting the PXE boot agent utility program PXE boot agent utility menu choicesBanner Message Timeout Pre-boot Wake on LANCommand-line interface Ipmi Shell Link SpeedUpdating and configuring the Bios Configuring Linux Configuring Red Hat Enterprise Linux ESOriginal /etc/lilo.conf contents Add the following five lines between the two title= sections Original /boot/grub/grub.conf contents Suse Sles 8.0 configuration Append the following text to the first title line Configuring a Microsoft Windows operating system Original bootcfg program outputInstalling the OSA SMBridge management utility program Modified bootcfg program outputUsing the baseboard management controller utility programs Using the OSA SMBridge management utility program Using the SAS/SATA Configuration Utility program Starting the SAS/SATA Configuration Utility programUsing ServeRAID Manager SerialSelect Utility menu choicesConfiguring the controller Using express configurationUsing custom configuration Click Express configurationUsing the Scalable Partition Web Interface Viewing the configurationCreating a scalable partition Page Configuring the server Page Deleting a scalable partition Page Updating IBM Director Page Appendix. Notices TrademarksImportant notes Product recycling and disposal Page Index LED SAS Memory-mirroring configuration Page Part Number 31R1871