IBM 71455DU manual Server controls, connectors, LEDs, and power, Front view

Page 21

Server controls, connectors, LEDs, and power

This section describes the controls, connectors, and light-emitting diodes (LEDs) and how to turn the server on and off.

Front view

The following illustration shows the controls, LEDs, and connectors on the front of the server.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electrostatic-discharge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connector

Hard disk drive

 

Hard disk drive

Operator information

status LED

 

activity LED

panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD-eject button

DVD drive activity LED

Hard disk drive status LED: If a ServeRAID-8i adapter is installed, when this LED is lit it indicates that the associated hard disk drive has failed. If the LED flashes slowly (one flash per second), the drive is being rebuilt. If the LED flashes rapidly (three flashes per second), the controller is identifying the drive.

Hard disk drive activity LED: On some server models, each hot-swap hard disk drive has an activity LED. When this LED is flashing, it indicates that the drive is in use.

Operator information panel: This panel contains controls and LEDs. The following illustration shows the controls and LEDs on the operator information panel.

Power-control button

Information LED

USB connector

Release latch

Power-on LED

Hard disk drive activity LED Locator LED

System-error LED

The following controls, connectors, and LEDs are on the operator information panel:

vUSB connector: Connect a USB device to this connector.

vPower-control button: Press this button to turn the server on and off manually. A power-control-button shield comes with the server.

vInformation LED: When this LED is lit, it indicates that there is a suboptimal condition in the server and that light path diagnostics will light an additional LED to help isolate the condition. If the LOG LED on the light path diagnostics panel is lit, information is available in the baseboard management controller (BMC) log or in the system-event log about the condition. The condition might be that the BMC log is full or almost full.

Chapter 1. The System x3950 and System x3950 E server 9

Image 21
Contents User’s Guide Page User’s Guide Page Contents Page Safety Page To Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb Page Related documentation System x3950 and System x3950 E serverProblem Determination and Service Guide Features and specifications Features and specifications What your server offers PowerExecutive Redundant connection Light path diagnosticsRedundant cooling and power capabilities Integrated network supportReliability, availability, and serviceability IBM Director UpdateXpress programFront view Server controls, connectors, LEDs, and powerPage Rear view Server power features Turning off the server Turning on the serverPage Server components Installing optionsJumper name Description Board internal connectors and jumpersMemory-card LEDs Memory-card connectorsMicroprocessor-board connectors and LEDs PCI-X board LEDs PCI-X board connectorsSAS-backplane connectors Installation guidelines System reliability guidelines Working inside the server with the power onRemoving the cover and bezel Handling static-sensitive devicesInstalling a hot-swap power supply Locking latch Locking handle open Installing an adapter ServeRAID-8i adapter ServeRAID-8i slot LED Adapter guide Installing a hot-swap hard disk drive Installing options Memory card order Dimm pair Memory moduleActive Memory Select Memory Settings Select Memory Mirroring Settings Adding and replacing a memory card Adding a memory cardHot-replacing a memory card Installing a Dimm Installing DIMMsDcac Hot-swapping DIMMs Installing options Hot-adding DIMMs Dimm Microprocessor Microprocessor installation order Installing a microprocessor Air baffle Heat sink Microprocessor connector Microprocessor- release lever Completing the installation Connecting the cables Rear viewFront view Updating the server configuration Two-node configurationSMP Expansion cabling Four-node configuration Protective cover Eight-node configuration Node SMP Expansion cable Page Installing options Page Boot Menu program Configuration/Setup Utility programGigabit Ethernet controller configuration process SAS/SATA Configuration Utility programUsing the Configuration/Setup Utility program Starting the Configuration/Setup Utility programConfiguration/Setup Utility menu choices Administrator Password Power-on PasswordSystem Card Data Devices and I/O PortsMemory Settings Advanced SetupRSA II Settings System Partition VisibilityBMC Post Watchdog Timeout Baseboard management controller BMC settingsBMC Serial Port Access Mode Reboot system on NMIPower-on password PasswordsAdministrator password Using the ServerGuide Setup and Installation CDSetup and configuration overview ServerGuide featuresInstalling your operating system without ServerGuide Typical operating-system installationUsing the Boot Menu program Download section, click Downloads & driversUsing the PXE boot agent utility program Configuring the Gigabit Ethernet controllerStarting the PXE boot agent utility program PXE boot agent utility menu choicesPre-boot Wake on LAN Banner Message TimeoutCommand-line interface Ipmi Shell Link SpeedUpdating and configuring the Bios Configuring Red Hat Enterprise Linux ES Configuring LinuxOriginal /etc/lilo.conf contents Add the following five lines between the two title= sections Original /boot/grub/grub.conf contents Suse Sles 8.0 configuration Append the following text to the first title line Original bootcfg program output Configuring a Microsoft Windows operating systemModified bootcfg program output Installing the OSA SMBridge management utility programUsing the baseboard management controller utility programs Using the OSA SMBridge management utility program Starting the SAS/SATA Configuration Utility program Using the SAS/SATA Configuration Utility programUsing ServeRAID Manager SerialSelect Utility menu choicesUsing express configuration Configuring the controllerUsing custom configuration Click Express configurationViewing the configuration Using the Scalable Partition Web InterfaceCreating a scalable partition Page Configuring the server Page Deleting a scalable partition Page Updating IBM Director Page Trademarks Appendix. NoticesImportant notes Product recycling and disposal Page Index LED SAS Memory-mirroring configuration Page Part Number 31R1871