SATO 200i manual Interface Specifications

Page 14

Unit 3: Interface Secifications

INTERFACE SPECIFICATIONS

This chapter presents the printer interface types and their specifications. These specifications include detailed information to assist in the selection of the most appropriate method for the printer to interface with the host. The acceptable interface methods are:

•802.11B Wireless

•RS232C Serial

•Infrared Rays (IrDA)

•Bluetooth

Following the selection of the desired interface, proceed to the following unit for instructions on how to Configure the printer for that interface type.

WARNING: NEVER CONNECT OR DISCONNECT INTERFACE CABLES (OR USE A SWITCH BOX) WITH POWER APPLIED TO EITHER THE HOST OR THE PRINTER. THIS MAY CAUSE DAMAGE TO THE INTERFACE CIRCUITRY IN THE PRINTER/HOST AND IS NOT COVERED BY WARRANTY.

SATO MB2i Service Manual

PN 9001145B

Page 3-2

Image 14

Contents MB200i Printer Sato America, Inc Table of Contents Adjustment Procedures Introduction About this Manual General Description Theory of OperationSwitches and Indicators SwitchesTechnical Data Environmental Physical CharacteristicsPower ProcessingCharacter Font Capabilities Character Control BAR Code CapabiltiesInterface Specifications Interface Specifications AD-HOC ConnectivityInterface Specifications 802.11B Wireless Interface 802.11B Wireless SpecificationsREADY/BUSY Cable Requirements DB9 RS232C SpecificationsRS232C Serial Interface Host Direction PIN PrinterInfrared Rays Irda Irda Specifications Standard ProtocolIrda Specifications BHT Protocol Irda Specifications Ircomm Protocol Irda Specifications IrOBEX ProtocolBluetooth ACK/NAK Protocol ALL Interface TypesReceive Buffer Printer Setup AD-HOC Connectivity3a/b, Sato MB200i Properties Sato MB200i Configuration Tool Computer Setup Network ConnectionsAdvanced 10, Wireless Network Properties 12a/b, Ports 14, TCP/IP Wizard Welcome Screen 16, TCP/IP Wizard Exit Screen 17, Sato MB200i Properties Display Fields LCD Screens Maintenance Mode LCD DisplayIcon Description Battery LevelDisplay Fields Wireless Field Strength Operational StatusLCD Screens Normal Mode StatusTest Print Mode Status LCD Detail Startup Status LCD DetailHEX Dump Mode Status LCD Detail Default Setting Mode Status LCD DetailFactory Clear Mode Status LCD Detail Printer Errors Status LCD Detail LCD Setup Status Detail Maintenance ModeMaintenance Mode Status LCD Detail Wireless LAN Status LCD Detail Printer Configuration Printer Configuration Configuration ModesRS232C Quick Reference Table Description DIP Switches Head Printer ConfigurationFactory Defaults DSW1 DSW2 DSW3 DSW4 Irda Quick Reference Table Description DIP Switches HeadUser Test Print Mode Opened Configuration Modes Normal ModePower = OFF Label Sensor SelectionManual Dispense ModeAuto Download Mode Orange and entersUnit 5 Printer Configuration Font Download Mode Format storage area if Never doneStatus Description Acsii HEX TransferOnline Command Mode Online Command ModeCRC Cyclic Redundancy Check Mode CRC Check ModeSleep & AUTO-OFF Mode Sleep & Auto-Off ModeUnit 5 Printer Configuration PN 9001145B Troubleshooting Error Signals LED Mode DescriptionUneven Print Darkness Image VoidsLight Print Images Smeared Print ImagesInterface Troubleshooting CHK Troubleshooting StepTest Print Troubleshooting HEX Dump ModeTest Print Mode Test Label PrintingReplacement Procedures Replacement Procedures Print Head ReplacementDispense BAR Replacement 1b, Print Head Replacement2b, Despense Bar Replacement Platen Roller Replacement 3a, Platen Roller ReplacementDispense Roller Replacement Dispenser RollerMain Circuit Board a Replacement Main Circuit Board a ReplacementMain Circuit Board B Replacement Main Circuit Board B ReplacementPanel & LCD Board Replacement Panel & LCD Board ReplacementEYE-MARK Sensor Replacement 8a, Eye-Mark Sensor Replacement8c, Eye-Mark Sensor Replacement GAP Sensor Replacement 9a, Gap Sensor ReplacementCOVER-OPEN Sensor Replacement 9b, Gap Sensor Replacement10b, Cover-Open Sensor Replacement Drive Gear Replacement 11, Gear ReplacementDrive Motor Replacement 12, Drive Motor ReplacementAdjustment Procedures Adjustment Procedures Pitch AdjustmentPrint Darkness Print DarknessDefault Setting Mode Print + PowerFactory Clear Mode Factory Clear ModeUnit 8 Adjustment Procedures PN 9001145B Charts & Diagrams Cover Removal DiagramCover Removal Diagram 1a, Cover Removal Diagram1b, Housing Cover Removal Unit 9 Charts & Diagrams PN 9001145B