SATO 408e manual Operator Panel

Page 28

Section 2. Installation

minimum of 0.67 in. (17mm) to a maximum of 2.5 in. (64 mm), and the Eye-Mark from a minimum of 0.25 in. (6mm) to a maximum of 2.1 in. (53mm).

OPERATOR PANEL

CL608e and CL612e

 

 

POWER

LINE

LABEL

RIBBON ERROR

LINE

 

 

FEED

Reserved

DSW2

DSW3

LCD

DISPLAY

PANEL

DISPLAY

PITCH

PRINT

OFFSET

The CL608e/CL612e Operator Panel consists of five LED indicators, two momentary contact switches, three DIP switches, four adjustment potentiometers and one LCD Display. All of these are accessible from the front of the printer. They are used to set the printer operating parameters and to indicate the status of the printer to the operator. After you power on the printer, familiarize yourself with the keys and indicators as it will help you understand the configuration process.

PRINT:

Potentiometer to adjust print darkness (fine tuning).

OFFSET:

Potentiometer to adjust amount of back/forward feed

 

for dispenser/cutter/tear-off bar position (+/-3.75 mm)

PITCH:

Potentiometer to adjust home position of the label

 

(+/- 3.75 mm). Affects stop position of label feed, print

 

position and dispense position.

DISPLAY:

Potentiometer to adjust the contrast of the LCD.

POWER:

LED, illuminated when the power is on.

Page 2-12

PN 9001074 Rev. B

SATO CL Series “e” Printers

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Section Printer Overview IntroductionGeneral Printer Specifications SpecificationPotentiometer Adjustments Character Fonts CL408e CL608e CL412e CL612eBAR Codes MSI PostnetPower Requirements PhysicalOptional Accessories AccessoryThis page left intentionally blank Section Installation Unpacking and Parts Identification CL6XX PackagingSetting UP the Printer CL608e and CL612e Loading LABELS, Tags and RibbonLoading Labels or Tags Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B CL408e and CL412e Loading Labels and TagsLabel Hold Down Open the Top and Front Access Doors Head AssemblyThrough the Print Head Assembly Close the Print Head Assembly byLabel Sensor Adjustments Operator Panel Error LabelRibbon OnlineLocated behind the Front Access Door. Potentiometer Option Connector StatusLabel Taken ThresholdRear Panel EXTPower 57-60140Switches and Sensors Head Open Switch Front Access DoorRibbon End Sensor Label Sensor UnitThis page left intentionally blank Section Configuration Printer DIP Switch ConfigurationDIP Switch Panels RS232 Transmit/Receive Setting located on RS232 I/F ModuleConfiguration Printer Set UpHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Switch Selections Default SettingsSoftware Default Settings Potentiometer Adjustments Backfeed OffsetDisplay LCD Panel Printer Configuration Normal Mode Online QTY000000Offline Print Darkness 1 2 3 4 Print Speed 4 6Pitch Offset + 00mm Cancel Print JOB YES no Completed Advanced ModeZero Slash YES no Auto Online Print Offset SET Calendar YES noIgnore CR/LF YES no Card Mode Character Pitch Fixed Prop Advanced ModeConfiguration Configuration Service Mode Advanced Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Test Print Mode Counter ModeCounters Mode Default Setting Mode Test Print Mode Configuration Test Print SizeDefault Setting YES no Default Setting Completed Press Feed KEY to Stop PrintingALT.PROTOCOL Default Complete Clear NON-STANDARD ProtocolDownload User Defined Protocol Codes User Download Press the Line KEY User Download WaitingHEX Dump Mode This page left intentionally blank Section Cleaning and Maintenance Procedures ALL ModelsAdjusting the Print Quality Darkness PrintPrint Cleaning the Print HEAD, Platen and RollersPrint Speed Cleaning the Platen and Rollers Open the Label Access DoorReplacing the Print Head Cleaning the Sensors Supplies Needed Sato SA070 Cleaning KitHold-Down when it is Hold-Down is springReplacing the Fuse Supplies needed 250V 3A FuseSupplies needed Cleaning the Print Head Cleaning the Print Head and PlatenCleaning the Platen Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Section Interface Specifications Interface TypesSingle Job Buffer Receive BufferMulti Job Buffer Electrical Specifications Printer ConnectorCable Connector IEEE1284 Parallel InterfaceSignal Level PIN Signal DirectionCable Data StreamsOptional RS232C Serial Interface General SpecificationsPIN Assignments PIN Direction Signal Definition Cable RequirementsREADY/BUSY Flow Control DB9On/X-Off Flow Control Universal Serial BUS USB Optional InterfaceData Streams Local Area Network LAN Optional Interface BI-DIRECTIONAL CommunicationsENQUIRE/ACK/NAK Enquire ENQCancel can Print JobPrint Stop DLE Print Start DC1Status Byte Definition, Bi-Com Protocol Status Response EXT Connector PIN Direction Signal DescriptionStandard Operation Error Signals Repeat PrintInitial Checklist Section TroubleshootingUsing the IEEE1284 Parallel Interface Troubleshooting Using the RS232C Serial Interface Error Signals LED LCD Audible Error Condition To Clear Message BeepAppendix a Optional Accessories InstallationLabel Rewinder ALL Models Removing and Unwinding the RollLabel Cutter ALL Models Operator SetupGeneral Operation Label Dispense Option Label Dispenser Routing, CL608e/CL612eOpen the Top Access Door and the Front Access Door Label Dispense Option is ready for useClose the Top Access Cover Label Dispenser Routing, CL408e/CL412eA-6 PN 9001074 Rev. B Sato CL Series e Printers Error Handling Error Description Indication RemedyPcmcia Memory Cards ALL Models DescriptionInternal Flash ROM Memory Expansion ALL Models Calendar ALL Models PLUG-IN Interface Modules ALL ModelsRemove the two Interface Module Retaining Screws Replace the two Interface Card Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents