SATO 408e manual Loading LABELS, Tags and Ribbon, CL608e and CL612e, Loading Labels or Tags

Page 20

Section 2. Installation

LOADING LABELS, TAGS AND RIBBON

CL608e and CL612e

 

 

LOADING LABELS OR TAGS

1.Open the Side Access Door by swinging it up and to the left. The hinge system automatically dampens the movement to prevent the door from inadvertently falling and possibly causing injury to the operator.

2.Open the Print Head Assembly by pushing the Head Latch toward the rear of the printer. The Print Head Assembly is spring-loaded and will automatically open as soon as the Head Latch is disengaged.

Head Latch

3.Push the Label Supply Guide to the outside of the printer to give the maximum label width.

4.Release the Label Roll Support by pulling outward at the top and swing it down and out of the way.

5.If using roll labels (or tags), load the roll onto the Label Supply Spindle so that the printing side of the labels faces upwards as it unwinds from the roll. The labels should be wound face-in. Push the roll all the way to the inside of the printer and push the Label Supply Guide snugly against the outside of the label roll.

6.If using fanfold labels (or tags) set them on a flat surface behind the printer. Pass the labels (printing side up) through the slot and under the Label Supply Spindle.

7.Open the Label Hold-Down by squeezing the green tab and the release tab together. The Label Hold-down is spring loaded and will open automatically when the latch is disengaged. Feed the labels under the Label Guide, under the Label Hold-Down, through the Print Head Assembly and out the front of the printer.

8.Inspect the label routing and verify that the path matches that illustrated in the Label Loading

Sensor Adjust

Cap Screw

Sensor Adjust

Tab

Label Hold-Down

Page 2-4

PN 9001074 Rev. B

SATO CL Series “e” Printers

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Section Printer Overview IntroductionGeneral Printer Specifications SpecificationPotentiometer Adjustments Character Fonts CL408e CL608e CL412e CL612eBAR Codes MSI PostnetPower Requirements PhysicalOptional Accessories AccessoryThis page left intentionally blank Section Installation Unpacking and Parts Identification CL6XX PackagingSetting UP the Printer Loading Labels or Tags Loading LABELS, Tags and RibbonCL608e and CL612e Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B CL408e and CL412e Loading Labels and TagsLabel Hold Down Open the Top and Front Access Doors Head AssemblyThrough the Print Head Assembly Close the Print Head Assembly byLabel Sensor Adjustments Operator Panel Error LabelRibbon OnlineLocated behind the Front Access Door. Potentiometer Option Connector StatusLabel Taken ThresholdRear Panel EXTPower 57-60140Switches and Sensors Head Open Switch Front Access DoorRibbon End Sensor Label Sensor UnitThis page left intentionally blank Section Configuration Printer DIP Switch ConfigurationDIP Switch Panels RS232 Transmit/Receive Setting located on RS232 I/F ModuleConfiguration Printer Set UpHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Software Default Settings Default SettingsSwitch Selections Potentiometer Adjustments Backfeed OffsetDisplay LCD Panel Printer Configuration Normal Mode Online QTY000000Offline Print Darkness 1 2 3 4 Print Speed 4 6Pitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Print Offset SET Calendar YES noIgnore CR/LF YES no Card Mode Character Pitch Fixed Prop Advanced ModeConfiguration Configuration Service Mode Advanced Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Counters Mode Counter ModeTest Print Mode Default Setting Mode Test Print Mode Configuration Test Print SizeDefault Setting YES no Default Setting Completed Press Feed KEY to Stop PrintingALT.PROTOCOL Default Complete Clear NON-STANDARD ProtocolDownload User Defined Protocol Codes User Download Press the Line KEY User Download WaitingHEX Dump Mode This page left intentionally blank Section Cleaning and Maintenance Procedures ALL ModelsAdjusting the Print Quality Darkness PrintPrint Speed Cleaning the Print HEAD, Platen and RollersPrint Cleaning the Platen and Rollers Open the Label Access DoorReplacing the Print Head Cleaning the Sensors Supplies Needed Sato SA070 Cleaning KitHold-Down when it is Hold-Down is springReplacing the Fuse Supplies needed 250V 3A FuseCleaning the Platen Cleaning the Print Head and PlatenSupplies needed Cleaning the Print Head Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Section Interface Specifications Interface TypesMulti Job Buffer Receive BufferSingle Job Buffer Electrical Specifications Printer ConnectorCable Connector IEEE1284 Parallel InterfaceSignal Level PIN Signal DirectionCable Data StreamsPIN Assignments General SpecificationsOptional RS232C Serial Interface PIN Direction Signal Definition Cable RequirementsREADY/BUSY Flow Control DB9Data Streams Universal Serial BUS USB Optional InterfaceOn/X-Off Flow Control Local Area Network LAN Optional Interface BI-DIRECTIONAL CommunicationsENQUIRE/ACK/NAK Enquire ENQCancel can Print JobPrint Stop DLE Print Start DC1Status Byte Definition, Bi-Com Protocol Status Response EXT Connector PIN Direction Signal DescriptionStandard Operation Error Signals Repeat PrintUsing the IEEE1284 Parallel Interface Section TroubleshootingInitial Checklist Troubleshooting Using the RS232C Serial Interface Error Signals LED LCD Audible Error Condition To Clear Message BeepAppendix a Optional Accessories InstallationLabel Rewinder ALL Models Removing and Unwinding the RollGeneral Operation Operator SetupLabel Cutter ALL Models Label Dispense Option Label Dispenser Routing, CL608e/CL612eOpen the Top Access Door and the Front Access Door Label Dispense Option is ready for useClose the Top Access Cover Label Dispenser Routing, CL408e/CL412eA-6 PN 9001074 Rev. B Sato CL Series e Printers Error Handling Error Description Indication RemedyPcmcia Memory Cards ALL Models DescriptionInternal Flash ROM Memory Expansion ALL Models Calendar ALL Models PLUG-IN Interface Modules ALL ModelsRemove the two Interface Module Retaining Screws Replace the two Interface Card Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents