SATO 408e manual Pitch Offset + 00mm

Page 47

PITCH OFFSET + 00mm

Section 3. Configuration

The label Pitch is the distance from the leading edge (the edge that comes out of the printer first) of a label and the leading edge of the next label. The leading edge position of the label can be adjusted relative to the print head +/- 49mm in increments of 1mm. Once the position is set, it can be fine adjusted +/- 3.75mm using the PITCH potentometer on the Adjustment Panel.

1.The cursor will initially be positioned over the Pitch Direction setting. Pressing the LINE key will step the setting to the positive (+) or negative (-) selection. A positive selection moves the leading edge of the label forward (away from the print head) while a negative selection moves the leading edge of the label back into the mechanism.

2.Once the correct direction is selected, pressing the FEED key will accept the setting and advance the cursor to the Offset selection.

3.Use the LINE key to step the first digit of the counter to the desired setting. The display will increment one step each time the LINE key is pressed. The reading will advance to a setting of 4 after which it will automatically wrap and start at 0 again.

4.Press the FEED key to accept the setting and advance the cursor to the second digit. Again use the LINE key to step to the desired setting. Once it is correct, pressing the FEED key will step to the next adjustment.

You may wish to print a test label after completing the adjustments to ensure they are correct.

ABCDEFG

ABCDEFG

ABCDEFG

Sensor Position

Moved with negative (-) offset to print on leading edge of the label

Leading edge of the label as detected by

Original (0 offset) first line print position

Moved with positive

(+)offset to print on trailing edge of label

SATO CL Series “e” Printers

PN 9001074 Rev. B

Page 3-11

Page 46 Page 48
Image 47
Page 46 Page 48
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Introduction Section Printer OverviewSpecification General Printer SpecificationsPotentiometer Adjustments CL408e CL608e CL412e CL612e Character FontsMSI Postnet BAR CodesPhysical Power RequirementsAccessory Optional AccessoriesThis page left intentionally blank Section Installation CL6XX Packaging Unpacking and Parts IdentificationSetting UP the Printer Loading Labels or Tags Loading LABELS, Tags and RibbonCL608e and CL612e Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B Loading Labels and Tags CL408e and CL412eLabel Hold Down Close the Print Head Assembly by Open the Top and Front Access DoorsHead Assembly Through the Print Head AssemblyLabel Sensor Adjustments Operator Panel Online ErrorLabel RibbonLocated behind the Front Access Door. Potentiometer Threshold Option ConnectorStatus Label TakenEXT Rear Panel57-60140 PowerSwitches and Sensors Label Sensor Unit Head Open SwitchFront Access Door Ribbon End SensorThis page left intentionally blank RS232 Transmit/Receive Setting located on RS232 I/F Module Section ConfigurationPrinter DIP Switch Configuration DIP Switch PanelsPrinter Set Up ConfigurationHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Software Default Settings Default SettingsSwitch Selections Backfeed Offset Potentiometer AdjustmentsDisplay LCD Panel Printer Configuration Print Darkness 1 2 3 4 Print Speed 4 6 Normal ModeOnline QTY000000 OfflinePitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed SET Calendar YES no Print OffsetIgnore CR/LF YES no Character Pitch Fixed Prop Advanced Mode Card ModeConfiguration Configuration Advanced Mode Service Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Counters Mode Counter ModeTest Print Mode Press Feed KEY to Stop Printing Default Setting ModeTest Print Mode Configuration Test Print Size Default Setting YES no Default Setting CompletedUser Download Press the Line KEY User Download Waiting ALT.PROTOCOL Default CompleteClear NON-STANDARD Protocol Download User Defined Protocol CodesHEX Dump Mode This page left intentionally blank Darkness Print Section Cleaning and MaintenanceProcedures ALL Models Adjusting the Print QualityPrint Speed Cleaning the Print HEAD, Platen and RollersPrint Open the Label Access Door Cleaning the Platen and RollersReplacing the Print Head Hold-Down is spring Cleaning the SensorsSupplies Needed Sato SA070 Cleaning Kit Hold-Down when it isSupplies needed 250V 3A Fuse Replacing the FuseCleaning the Platen Cleaning the Print Head and PlatenSupplies needed Cleaning the Print Head Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Interface Types Section Interface SpecificationsMulti Job Buffer Receive BufferSingle Job Buffer IEEE1284 Parallel Interface Electrical SpecificationsPrinter Connector Cable ConnectorData Streams Signal LevelPIN Signal Direction CablePIN Assignments General SpecificationsOptional RS232C Serial Interface DB9 PIN Direction Signal DefinitionCable Requirements READY/BUSY Flow ControlData Streams Universal Serial BUS USB Optional InterfaceOn/X-Off Flow Control Enquire ENQ Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications ENQUIRE/ACK/NAKPrint Start DC1 Cancel canPrint Job Print Stop DLEStatus Byte Definition, Bi-Com Protocol Status Response PIN Direction Signal Description EXT ConnectorStandard Operation Repeat Print Error SignalsUsing the IEEE1284 Parallel Interface Section TroubleshootingInitial Checklist Troubleshooting Using the RS232C Serial Interface LED LCD Audible Error Condition To Clear Message Beep Error SignalsRemoving and Unwinding the Roll Appendix a Optional AccessoriesInstallation Label Rewinder ALL ModelsGeneral Operation Operator SetupLabel Cutter ALL Models Label Dispenser Routing, CL608e/CL612e Label Dispense OptionLabel Dispense Option is ready for use Open the Top Access Door and the Front Access DoorLabel Dispenser Routing, CL408e/CL412e Close the Top Access CoverA-6 PN 9001074 Rev. B Sato CL Series e Printers Description Error HandlingError Description Indication Remedy Pcmcia Memory Cards ALL ModelsInternal Flash ROM Memory Expansion ALL Models Replace the two Interface Card Retaining Screws Calendar ALL ModelsPLUG-IN Interface Modules ALL Models Remove the two Interface Module Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents