SATO 408e manual GAP Input

Page 55

GAP [X.XV]

INPUT [X.XV]

GAP [X.XV]

INPUT [X.XV]

Section 3. Configuration

The “e” Series printers determine the location of the leading edge of the label by measuring the difference between light levels when it sees either a label edge or a black “EYE” mark. This adjustment allows you to manually set the threshold voltage level, between the maximum and minimum light levels. DIP switch DSW2-2 selects the sensor type. If DSW2-2 is in the OFF position, the setting will be for a See-Thru (or Gap) sensor and the LCD will display “GAP” on the top line along with the current setting. If DSW2-2 is in the ON position, the LCD will display “EYE” on the top line with its current setting. If the value entered for the bottom line setting is “0.0V”, then the printer will automatically calculate the setting when the first label is fed after the printer is powered on or the head is closed. There are some instances where the automatically calculated value must be adjusted to ensure reliable label feeding, such as when the backing opacity or the reflectance of the EYE mark varies significantly within a roll of labels or between label rolls. In these instances the value should be set using the following procedures.

GAP - When setting the “gap” threshold, the voltage shown on the top line of the display must be measured with nothing but the backing in the sensor and then again with a label still attached to the backing. The formula to be used for setting the threshold is:

(High Voltage Level + Low Voltage Level) x 0.5 = Start Value

1.Insert a label still attached to the backing into the sensor and close the Label Hold-Down. Record the voltage shown on the top line of the LCD panel. This line should have the message “GAP” on the top line (DIP switch DSW2-2 = OFF). Make sure the label is all the way under the sensor.

2.Strip the label from the backing and insert the backing strip under the sensor and close the Label Lid. Record the voltage shown on the top line of the LCD panel. The voltage ranges measured should be within the following range

Backing without label = 0.5V or less

Backing with label = 1.0V ≥ the low value

If the measured values are outside this range, you may have trouble in finding a value that will work properly under all conditions. If this is the case, a higher quality label may be needed to get adequate performance.

3.Calculate the starting point voltage using the formula.

4.Use the LINE key to step the counter to the desired setting. The display will increment one step for each time the LINE key is pressed. If the LINE key is held pressed for more than two seconds, it will automatically go into the fast scroll mode. The reading will advance to a setting of 3.3 (the maximum voltage) after which it will automatically wrap and start at “0.0” again. If a value of “0.0” is set,the printer will automatically set the level each time the printer is powered on with labels loaded or the head is closed.

5.Once the setting is correct, pressing the FEED key will accept the setting and advance to the Online Feed display.

SATO CL Series “e” Printers

PN 9001074 Rev. B

Page 3-19

Page 54 Page 56
Image 55
Page 54 Page 56
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Introduction Section Printer OverviewSpecification General Printer SpecificationsPotentiometer Adjustments CL408e CL608e CL412e CL612e Character FontsMSI Postnet BAR CodesPhysical Power RequirementsAccessory Optional AccessoriesThis page left intentionally blank Section Installation CL6XX Packaging Unpacking and Parts IdentificationSetting UP the Printer CL608e and CL612e Loading LABELS, Tags and RibbonLoading Labels or Tags Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B Loading Labels and Tags CL408e and CL412eLabel Hold Down Close the Print Head Assembly by Open the Top and Front Access DoorsHead Assembly Through the Print Head AssemblyLabel Sensor Adjustments Operator Panel Online ErrorLabel RibbonLocated behind the Front Access Door. Potentiometer Threshold Option ConnectorStatus Label TakenEXT Rear Panel57-60140 PowerSwitches and Sensors Label Sensor Unit Head Open SwitchFront Access Door Ribbon End SensorThis page left intentionally blank RS232 Transmit/Receive Setting located on RS232 I/F Module Section ConfigurationPrinter DIP Switch Configuration DIP Switch PanelsPrinter Set Up ConfigurationHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Switch Selections Default SettingsSoftware Default Settings Backfeed Offset Potentiometer AdjustmentsDisplay LCD Panel Printer Configuration Print Darkness 1 2 3 4 Print Speed 4 6 Normal ModeOnline QTY000000 OfflinePitch Offset + 00mm Cancel Print JOB YES no Completed Advanced ModeZero Slash YES no Auto Online SET Calendar YES no Print OffsetIgnore CR/LF YES no Character Pitch Fixed Prop Advanced Mode Card ModeConfiguration Configuration Advanced Mode Service Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Test Print Mode Counter ModeCounters Mode Press Feed KEY to Stop Printing Default Setting ModeTest Print Mode Configuration Test Print Size Default Setting YES no Default Setting CompletedUser Download Press the Line KEY User Download Waiting ALT.PROTOCOL Default CompleteClear NON-STANDARD Protocol Download User Defined Protocol CodesHEX Dump Mode This page left intentionally blank Darkness Print Section Cleaning and MaintenanceProcedures ALL Models Adjusting the Print QualityPrint Cleaning the Print HEAD, Platen and RollersPrint Speed Open the Label Access Door Cleaning the Platen and RollersReplacing the Print Head Hold-Down is spring Cleaning the SensorsSupplies Needed Sato SA070 Cleaning Kit Hold-Down when it isSupplies needed 250V 3A Fuse Replacing the FuseSupplies needed Cleaning the Print Head Cleaning the Print Head and PlatenCleaning the Platen Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Interface Types Section Interface SpecificationsSingle Job Buffer Receive BufferMulti Job Buffer IEEE1284 Parallel Interface Electrical SpecificationsPrinter Connector Cable ConnectorData Streams Signal LevelPIN Signal Direction CableOptional RS232C Serial Interface General SpecificationsPIN Assignments DB9 PIN Direction Signal DefinitionCable Requirements READY/BUSY Flow ControlOn/X-Off Flow Control Universal Serial BUS USB Optional InterfaceData Streams Enquire ENQ Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications ENQUIRE/ACK/NAKPrint Start DC1 Cancel canPrint Job Print Stop DLEStatus Byte Definition, Bi-Com Protocol Status Response PIN Direction Signal Description EXT ConnectorStandard Operation Repeat Print Error SignalsInitial Checklist Section TroubleshootingUsing the IEEE1284 Parallel Interface Troubleshooting Using the RS232C Serial Interface LED LCD Audible Error Condition To Clear Message Beep Error SignalsRemoving and Unwinding the Roll Appendix a Optional AccessoriesInstallation Label Rewinder ALL ModelsLabel Cutter ALL Models Operator SetupGeneral Operation Label Dispenser Routing, CL608e/CL612e Label Dispense OptionLabel Dispense Option is ready for use Open the Top Access Door and the Front Access DoorLabel Dispenser Routing, CL408e/CL412e Close the Top Access CoverA-6 PN 9001074 Rev. B Sato CL Series e Printers Description Error HandlingError Description Indication Remedy Pcmcia Memory Cards ALL ModelsInternal Flash ROM Memory Expansion ALL Models Replace the two Interface Card Retaining Screws Calendar ALL ModelsPLUG-IN Interface Modules ALL Models Remove the two Interface Module Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents