SATO 408e manual EXT Connector, PIN Direction Signal Description

Page 86

Section 6. Interface Specifications

EXT CONNECTOR

The EXT connector on the rear panel of the CL Series “e” printers is intended for use with the external printer accessories such as label rewinders or applicators. The

14-pin Centronics type connector provides a choice of four different output signals along with various error conditions.

Pin Assignments

PIN

DIRECTION

SIGNAL DESCRIPTION

 

 

 

13

To Host

Vcc - +5V

 

 

 

10

To Host

Ribbon Near End - This pin goes high when the amount of ribbon

 

 

on the unwind shaft is approximately 46 feet (14 m). The output

 

 

will be low when the ribon is completely out.

 

 

 

4

To Host

Error - This pin goes low when the printer detects an error

 

 

condition such as head open or receiving buffer full.

 

 

 

7

To Printer

Reprint - A duplicate of the last label in a print job will be reprinted

 

 

when this signal is received.

 

 

 

5

To Printer

Print Start - The printer will print one label when this pin is pulled

 

 

to ground. This signal must be enabled by placing switch DSW3-5

 

 

on the Control Panel in the OFF position.

 

 

 

6

To Host

End Print - It is used to drive an applicator or other external device

 

 

requiring synchronization with the print cycle. You may choose

 

 

between four types of output signals using control panel DSW3-6

 

 

and DSW3-7 selections.See timing charts on next page.

 

 

 

1

To Host

Label Out - This pin goes low (0V) when a label out error exists.

 

 

 

3

To Host

Ribbon Out - This pin goes low (0V) when the ribbon is out.

 

 

 

2

Reference

Signal Ground

 

 

 

8

To Printer

Reserved

 

 

 

9

To Host

Off Line - This pin goes low (0V) when the printer if Off Line.

 

 

 

11

 

Reserved

 

 

 

12

To Host

+24V +/- 10% @2A - Power for external devices.

 

 

 

14

 

Frame Ground

 

 

 

 

 

 

NOTE: The signals on pins 1, 3, 4, 6, 9 and 10 each have an open collector output. These pins normally measure

+.07V maximum when a true condition exists. If a false condition occurs, the voltage will drop to 0V. To achieve a sig- nal level of +5V, you must add a 330 ohm, 1/4W pull-up resistor between the open collector output pin and Vcc (pin

13)as illustrated . This will provide a signal level of +5V for a true condition and 0V when a false condition exists. The maximum voltage that can be applied to these pins is +50V and the maximum current they can sink is 500 milliamps.

Page 6-12

PN 9001074 Rev. B

SATO CL Series “e” Printers

Page 85 Page 87
Image 86
Page 85 Page 87
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Section Printer Overview IntroductionGeneral Printer Specifications SpecificationPotentiometer Adjustments Character Fonts CL408e CL608e CL412e CL612eBAR Codes MSI PostnetPower Requirements PhysicalOptional Accessories AccessoryThis page left intentionally blank Section Installation Unpacking and Parts Identification CL6XX PackagingSetting UP the Printer Loading Labels or Tags Loading LABELS, Tags and RibbonCL608e and CL612e Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B CL408e and CL412e Loading Labels and TagsLabel Hold Down Through the Print Head Assembly Open the Top and Front Access DoorsHead Assembly Close the Print Head Assembly byLabel Sensor Adjustments Operator Panel Ribbon ErrorLabel OnlineLocated behind the Front Access Door. Potentiometer Label Taken Option ConnectorStatus ThresholdRear Panel EXTPower 57-60140Switches and Sensors Ribbon End Sensor Head Open SwitchFront Access Door Label Sensor UnitThis page left intentionally blank DIP Switch Panels Section ConfigurationPrinter DIP Switch Configuration RS232 Transmit/Receive Setting located on RS232 I/F ModuleConfiguration Printer Set UpHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Software Default Settings Default SettingsSwitch Selections Potentiometer Adjustments Backfeed OffsetDisplay LCD Panel Printer Configuration Offline Normal ModeOnline QTY000000 Print Darkness 1 2 3 4 Print Speed 4 6Pitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Print Offset SET Calendar YES noIgnore CR/LF YES no Card Mode Character Pitch Fixed Prop Advanced ModeConfiguration Configuration Service Mode Advanced Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Counters Mode Counter ModeTest Print Mode Default Setting YES no Default Setting Completed Default Setting ModeTest Print Mode Configuration Test Print Size Press Feed KEY to Stop PrintingDownload User Defined Protocol Codes ALT.PROTOCOL Default CompleteClear NON-STANDARD Protocol User Download Press the Line KEY User Download WaitingHEX Dump Mode This page left intentionally blank Adjusting the Print Quality Section Cleaning and MaintenanceProcedures ALL Models Darkness PrintPrint Speed Cleaning the Print HEAD, Platen and RollersPrint Cleaning the Platen and Rollers Open the Label Access DoorReplacing the Print Head Hold-Down when it is Cleaning the SensorsSupplies Needed Sato SA070 Cleaning Kit Hold-Down is springReplacing the Fuse Supplies needed 250V 3A FuseCleaning the Platen Cleaning the Print Head and PlatenSupplies needed Cleaning the Print Head Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Section Interface Specifications Interface TypesMulti Job Buffer Receive BufferSingle Job Buffer Cable Connector Electrical SpecificationsPrinter Connector IEEE1284 Parallel InterfaceCable Signal LevelPIN Signal Direction Data StreamsPIN Assignments General SpecificationsOptional RS232C Serial Interface READY/BUSY Flow Control PIN Direction Signal DefinitionCable Requirements DB9Data Streams Universal Serial BUS USB Optional InterfaceOn/X-Off Flow Control ENQUIRE/ACK/NAK Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications Enquire ENQPrint Stop DLE Cancel canPrint Job Print Start DC1Status Byte Definition, Bi-Com Protocol Status Response EXT Connector PIN Direction Signal DescriptionStandard Operation Error Signals Repeat PrintUsing the IEEE1284 Parallel Interface Section TroubleshootingInitial Checklist Troubleshooting Using the RS232C Serial Interface Error Signals LED LCD Audible Error Condition To Clear Message BeepLabel Rewinder ALL Models Appendix a Optional AccessoriesInstallation Removing and Unwinding the RollGeneral Operation Operator SetupLabel Cutter ALL Models Label Dispense Option Label Dispenser Routing, CL608e/CL612eOpen the Top Access Door and the Front Access Door Label Dispense Option is ready for useClose the Top Access Cover Label Dispenser Routing, CL408e/CL412eA-6 PN 9001074 Rev. B Sato CL Series e Printers Pcmcia Memory Cards ALL Models Error HandlingError Description Indication Remedy DescriptionInternal Flash ROM Memory Expansion ALL Models Remove the two Interface Module Retaining Screws Calendar ALL ModelsPLUG-IN Interface Modules ALL Models Replace the two Interface Card Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents