SATO Essential Cleaning and Maintenance for Your CL612E Printer
Page 66

Section 4: Cleaning and Maintenance

7.There is one metal roller used in guiding the labels through the printer. It should be cleaned of any residue or foreign material.

8.Repeat if necessary. The platen and rollers should be cleaned whenever foreign matter such as dust or adhesive is present.

REPLACING THE PRINT HEAD

CL608e and CL612e

 

 

The print head on the CL6XXe printers is a user-replaceable item. If it becomes damaged for any reason, it can be easily removed and replaced. Contact your local SATO representative for information on obtaining a new print head.

Supplies needed:No. 2 Phillips screwdriver (a magnetic tip is helpful)

1.Turn the printer off and remove the power cable.

2.Open the Label Access door.

3.Open the Print Head Assembly by pushing the Head Latch toward the rear of the printer. The Print Head Assembly is spring-loaded and will automatically open as soon as the Head Latch is disengaged.

4.Remove the ribbon from the Ribbon Rewind Spindle if necessary.

5.View the Print Head Assembly from the front of the printer. Locate the two mounting screws on the top of the assembly. They are accessible through the two holes in the Top Assembly Plate. Unscrew these two screws and set them aside.

6.The Print Head should now be loosened from the top of the assembly by grasping either side and carefully pulling it forward.

Mounting Screws

Signal

Connector

Print Head

Power

Connector

Page 4-4

9001074 Rev. B

SATO CL Series “e” Printers

Page 65 Page 67
Image 66
Page 65 Page 67
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Section Printer Overview IntroductionGeneral Printer Specifications SpecificationPotentiometer Adjustments Character Fonts CL408e CL608e CL412e CL612eBAR Codes MSI PostnetPower Requirements PhysicalOptional Accessories AccessoryThis page left intentionally blank Section Installation Unpacking and Parts Identification CL6XX PackagingSetting UP the Printer Loading LABELS, Tags and Ribbon CL608e and CL612eLoading Labels or Tags Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B CL408e and CL412e Loading Labels and TagsLabel Hold Down Through the Print Head Assembly Open the Top and Front Access DoorsHead Assembly Close the Print Head Assembly byLabel Sensor Adjustments Operator Panel Ribbon ErrorLabel OnlineLocated behind the Front Access Door. Potentiometer Label Taken Option ConnectorStatus ThresholdRear Panel EXTPower 57-60140Switches and Sensors Ribbon End Sensor Head Open SwitchFront Access Door Label Sensor UnitThis page left intentionally blank DIP Switch Panels Section ConfigurationPrinter DIP Switch Configuration RS232 Transmit/Receive Setting located on RS232 I/F ModuleConfiguration Printer Set UpHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Default Settings Switch SelectionsSoftware Default Settings Potentiometer Adjustments Backfeed OffsetDisplay LCD Panel Printer Configuration Offline Normal ModeOnline QTY000000 Print Darkness 1 2 3 4 Print Speed 4 6Pitch Offset + 00mm Advanced Mode Cancel Print JOB YES no CompletedZero Slash YES no Auto Online Print Offset SET Calendar YES noIgnore CR/LF YES no Card Mode Character Pitch Fixed Prop Advanced ModeConfiguration Configuration Service Mode Advanced Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Counter Mode Test Print ModeCounters Mode Default Setting YES no Default Setting Completed Default Setting ModeTest Print Mode Configuration Test Print Size Press Feed KEY to Stop PrintingDownload User Defined Protocol Codes ALT.PROTOCOL Default CompleteClear NON-STANDARD Protocol User Download Press the Line KEY User Download WaitingHEX Dump Mode This page left intentionally blank Adjusting the Print Quality Section Cleaning and MaintenanceProcedures ALL Models Darkness PrintCleaning the Print HEAD, Platen and Rollers PrintPrint Speed Cleaning the Platen and Rollers Open the Label Access DoorReplacing the Print Head Hold-Down when it is Cleaning the SensorsSupplies Needed Sato SA070 Cleaning Kit Hold-Down is springReplacing the Fuse Supplies needed 250V 3A FuseCleaning the Print Head and Platen Supplies needed Cleaning the Print HeadCleaning the Platen Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Section Interface Specifications Interface TypesReceive Buffer Single Job BufferMulti Job Buffer Cable Connector Electrical SpecificationsPrinter Connector IEEE1284 Parallel InterfaceCable Signal LevelPIN Signal Direction Data StreamsGeneral Specifications Optional RS232C Serial InterfacePIN Assignments READY/BUSY Flow Control PIN Direction Signal DefinitionCable Requirements DB9Universal Serial BUS USB Optional Interface On/X-Off Flow ControlData Streams ENQUIRE/ACK/NAK Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications Enquire ENQPrint Stop DLE Cancel canPrint Job Print Start DC1Status Byte Definition, Bi-Com Protocol Status Response EXT Connector PIN Direction Signal DescriptionStandard Operation Error Signals Repeat PrintSection Troubleshooting Initial ChecklistUsing the IEEE1284 Parallel Interface Troubleshooting Using the RS232C Serial Interface Error Signals LED LCD Audible Error Condition To Clear Message BeepLabel Rewinder ALL Models Appendix a Optional AccessoriesInstallation Removing and Unwinding the RollOperator Setup Label Cutter ALL ModelsGeneral Operation Label Dispense Option Label Dispenser Routing, CL608e/CL612eOpen the Top Access Door and the Front Access Door Label Dispense Option is ready for useClose the Top Access Cover Label Dispenser Routing, CL408e/CL412eA-6 PN 9001074 Rev. B Sato CL Series e Printers Pcmcia Memory Cards ALL Models Error HandlingError Description Indication Remedy DescriptionInternal Flash ROM Memory Expansion ALL Models Remove the two Interface Module Retaining Screws Calendar ALL ModelsPLUG-IN Interface Modules ALL Models Replace the two Interface Card Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents