SATO 408e manual Label Dispense Option, Label Dispenser Routing, CL608e/CL612e

Page 95

Appendix A: Optional Features

LABEL DISPENSE OPTION

CL608e and CL612e

 

 

The CL608e and CL612e Label Dispense Option is an external mechanism that provides the ability to print labels in the “demand” mode. It is attached to rear of the printer with two screws and is connected to the internal drive mechanism of the printer. When the label dispenser is installed and configured for operation, the printer dispenses one label at a time, peeling the backing from the label, which allows for immediate application to the product by the operator.

Operator Setup

The following steps should be taken to set up the Label Dispense Option.

1.Install the option using the instructions provided with the unit. The installation time is approximately 30 minutes.

2.Power the printer ON.

3.The printer must be configured to used the label dispenser option. Switches DSW3-1 and DSW3-2 on the front panel are used to configure the printer. To enable the dispenser, both DSW3-1and DSW3-2should be in the ON position.

4.Remove enough labels from the backing paper to provide 24 to 30 inches of backing free from labels.

5.Open the Print Head assembly and feed the backing paper through the print area in the normal manner.

6.At the label exit area, feed the backing paper down and behind the Knurled Roller, then back down and around the Backing Roller.

7.Feed the backing paper out the slot in the bottom rear of the printer and attach to the Backing Rewind Spindle.

Backing

Rewind

Spindle

Knurled

Roller

Backing

Roller

Label Dispenser Routing, CL608e/CL612e

SATO CL Series “e” Printers

PN 9001074 Rev. B

Page A-3

Image 95
Contents PN 9001074 Rev. B Sato CL Series e Printers 08/31/03 PN 9001074 Rev. B Preface Appendices Table of Contents Download User Defined Protocol Codes Hex Dump Mode Troubleshooting Preface This page left intentionally blank Introduction Section Printer OverviewSpecification General Printer SpecificationsPotentiometer Adjustments CL408e CL608e CL412e CL612e Character FontsMSI Postnet BAR CodesPhysical Power RequirementsAccessory Optional AccessoriesThis page left intentionally blank Section Installation CL6XX Packaging Unpacking and Parts IdentificationSetting UP the Printer Loading Labels or Tags Loading LABELS, Tags and RibbonCL608e and CL612e Installation Loading the Ribbon Sato CL Series e Printers PN 9001074 Rev. B Loading Labels and Tags CL408e and CL412eLabel Hold Down Close the Print Head Assembly by Open the Top and Front Access DoorsHead Assembly Through the Print Head AssemblyLabel Sensor Adjustments Operator Panel Online ErrorLabel RibbonLocated behind the Front Access Door. Potentiometer Threshold Option ConnectorStatus Label TakenEXT Rear Panel57-60140 PowerSwitches and Sensors Label Sensor Unit Head Open SwitchFront Access Door Ribbon End SensorThis page left intentionally blank RS232 Transmit/Receive Setting located on RS232 I/F Module Section ConfigurationPrinter DIP Switch Configuration DIP Switch PanelsPrinter Set Up ConfigurationHex Dump Selection DSW2-4. Selects Hex Dump mode DSW3-1 DSW3-2 Reserved for Future Use DSW3-2 Software Default Settings Default SettingsSwitch Selections Backfeed Offset Potentiometer AdjustmentsDisplay LCD Panel Printer Configuration Print Darkness 1 2 3 4 Print Speed 4 6 Normal ModeOnline QTY000000 OfflinePitch Offset + 00mm Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed SET Calendar YES no Print OffsetIgnore CR/LF YES no Character Pitch Fixed Prop Advanced Mode Card ModeConfiguration Configuration Advanced Mode Service Mode Service ModeGAP Input EYE Input Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default Counters Mode Counter ModeTest Print Mode Press Feed KEY to Stop Printing Default Setting ModeTest Print Mode Configuration Test Print Size Default Setting YES no Default Setting CompletedUser Download Press the Line KEY User Download Waiting ALT.PROTOCOL Default CompleteClear NON-STANDARD Protocol Download User Defined Protocol CodesHEX Dump Mode This page left intentionally blank Darkness Print Section Cleaning and MaintenanceProcedures ALL Models Adjusting the Print QualityPrint Speed Cleaning the Print HEAD, Platen and RollersPrint Open the Label Access Door Cleaning the Platen and RollersReplacing the Print Head Hold-Down is spring Cleaning the SensorsSupplies Needed Sato SA070 Cleaning Kit Hold-Down when it isSupplies needed 250V 3A Fuse Replacing the FuseCleaning the Platen Cleaning the Print Head and PlatenSupplies needed Cleaning the Print Head Replacing the Print Head Supplies Needed This page left intentionally blank Section Programming Reference This page left intentionally blank Interface Types Section Interface SpecificationsMulti Job Buffer Receive BufferSingle Job Buffer IEEE1284 Parallel Interface Electrical SpecificationsPrinter Connector Cable ConnectorData Streams Signal LevelPIN Signal Direction CablePIN Assignments General SpecificationsOptional RS232C Serial Interface DB9 PIN Direction Signal DefinitionCable Requirements READY/BUSY Flow ControlData Streams Universal Serial BUS USB Optional InterfaceOn/X-Off Flow Control Enquire ENQ Local Area Network LAN Optional InterfaceBI-DIRECTIONAL Communications ENQUIRE/ACK/NAKPrint Start DC1 Cancel canPrint Job Print Stop DLEStatus Byte Definition, Bi-Com Protocol Status Response PIN Direction Signal Description EXT ConnectorStandard Operation Repeat Print Error SignalsUsing the IEEE1284 Parallel Interface Section TroubleshootingInitial Checklist Troubleshooting Using the RS232C Serial Interface LED LCD Audible Error Condition To Clear Message Beep Error SignalsRemoving and Unwinding the Roll Appendix a Optional AccessoriesInstallation Label Rewinder ALL ModelsGeneral Operation Operator SetupLabel Cutter ALL Models Label Dispenser Routing, CL608e/CL612e Label Dispense OptionLabel Dispense Option is ready for use Open the Top Access Door and the Front Access DoorLabel Dispenser Routing, CL408e/CL412e Close the Top Access CoverA-6 PN 9001074 Rev. B Sato CL Series e Printers Description Error HandlingError Description Indication Remedy Pcmcia Memory Cards ALL ModelsInternal Flash ROM Memory Expansion ALL Models Replace the two Interface Card Retaining Screws Calendar ALL ModelsPLUG-IN Interface Modules ALL Models Remove the two Interface Module Retaining ScrewsA-10 PN 9001074 Rev. B Sato CL Series e Printers
Related manuals
Manual 86 pages 8.24 Kb

408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.