Star Micronics NP-415W, NP-215, NP-225 Reverse print set and reset GS B n Code 1D h + 42 h + n

Page 40

47) Reverse print set and reset :<< GS B n >>

 

Code

: < 1D > h + < 42 > h + n

* < 00nFF >h

Function

: Sets and resets reverse print.

 

*“n” is available only for the least significant bit.

*The characters incorporated and downloaded can be reverse printed.

*The right side space of character set by [Set right space of a character] is also included for reverse print. However, it does not cover the skipped space made by bit image, download bit image, NV bit image, barcode, HRI characters, horizontal tab, specify absolute position, specify relative position.

*It does not include the space between the lines.

*Reverse print has a priority over “underline specified”. If a character is reversed, the character is not underlined. However, the underline setting remains effective.

*If “highlight” or “double strike” is set on the reverse print, the print may result in damages.

48) Presenter eject mode selection

:<< ESC h n >>

 

Code

: < 1B > h + < 68 > h + n

* < 00n01 >h

Description

: Selects either “cramp eject” or “total eject” for the presenter paper eject

 

 

mode.

 

 

 

 

“n” indicates the following:

 

 

 

 

n (HEX)

Function

 

 

 

 

00

Cramp eject

 

 

 

01Total eject

Default value is “n” = [00]h

49) Back feed

:<< ESC B n >>

 

Code

: < 1B > h + < 42 > h + n

* < 00nFF >h

Description

: Feed the paper backward.

 

*Paper feed amount is specified by n dot line.

*Paper is not fed backward when 0 is set.

*If this command is used for many times, paper may be jammed. To avoid this problem, enter only once and feed paper in the forward direction.

*Double strike print is available by using this command.

*Considering the backlash, there may be a gap of printing.

*When data remains in the print line buffer, it first prints data, then back feeds.

*Paper might get jammed while a presenter is in use. In this regard, please do not use the command once paper is set in the presenter.

50) Software reset

:<< DC1 >>

Code

: < 11 > h

Description

: Restart the firmware as the same procedure as power on.

*This command is stored in the receive input buffer and activated in sequence.

*When the cutter is in a movement, soft reset is executed after finishing cutting.

37

Image 40
Contents Specifications for Read carefully Before Using the Printer Page NP 4 1 5 W Configuration Printer consists of the following components Codabar NW-7 CODE128 TOP Defects caused by dust or others This drawing is for NP-215P M3 screw holes to fix frame ground Frame ground wires Φ3.4 M3 screw holes to fix frame ground NP-325R This drawing is for NP-415WP ACK, BUSY, /STB, /ERROR, PE, SLCT, /INIT ErrorSTB InitPower Data STB Busy ACKXON XoffGND PD0 PD1PD2 PD3CSW1 CSW2LED+ PNEALM LED +ESC/POS OFFXON/XOFF DTR/DSR Processing error Error detection details Power OFF , /INITCN6 Control commands Control command table Feed pitch Font a Font B LSB MSB LSB MSB67DPI Data Underline set/reset ESC n Code 1B h + 2D h + n Bold print set/reset ESC E Code 1B h + 45 h + n Platen open Code 1B h + 7B h + n Barcode print GS k n Dn NUL Code 1D h + 6B h + n + Dn + 00 h MSB LSB 00 ≤n3 ≤01 h Code 1B h + 61 h + n 00 ≤n ≤02 h Description HEX Code 154 489 3908 1167 707 486 299 368 2940 Reverse print set and reset GS B n Code 1D h + 42 h + n Partition drive select GS % n Code 1D h + 25 h + n Page Page International character code table Parts Name QTY Material Treatment JST