Star Micronics NX-2400 user manual If you have problems with graphics

Page 58

nIf the printed characters don’t match the characters on the screen:

•Check DIP switches 2-2 to 2-4. When these switches are not all ON (back),

an international character set is selected and some ASCII symbols are changed to other characters. See Appendix D.

•Some software is not able to display international characters on the screen.

If you use an international character set you may want to paste labels on the keyboard.

•If you are using the IBM mode, check DIP switch l-7. Some international characters and symbols do not print when this switch is OFF (front).

nIf some printer commands are ignored or executed incor- rectly:

•Check that the setting of DIP switch l-6 matches the type of printer your software supports: ON (back) for Star or Epson; OFF (front) for IBM.

•A few commands are mutually exclusive. For example, you cannot get emphasized condensed printing.

nIf you have problems with horizontal tabulation:

•Don’t change the margins after setting tabs.

•Don’t change the print pitch after setting tabs. The physical positions of the tab stops do not adjust to the new print pitch.

H If you have problems with graphics:

•If you are using commercial software, check that it supports this printer, or a Star, Epson or IBM printer, and that DIP switch l-6 is set correctly: ON (back) for Star or Epson; OFF (front) for IBM.

•Use a hex dump to verify the codes the printer is receiving. See the graphics

command descriptions in Appendix B. Some computers insert unwanted

commands (such as carriage returns and line feeds) in graphics data, or change the values of certain codes.

•BASIC programs may require a WIDTH statement. Check your BASIC manual.

nIf you have problems with download characters:

•Check that DIP switch 2-l is OFF (front).

•Make the same checks as for graphics problems.

50

Image 58

Contents NX-2400 Page HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents With DOS and Basic Download Character Generator Chapter Platen Setting UP Remove the top coverInstall the ribbon cartridge Install the optional IC card Replace the top cowerConnect the printer to the computer Mount the paper guideSemiautomatic loading Figure l-7.Mounting the paper guide for single sheetsManual loading Loading and Parking Fanfold Forms 11. Closing the sprocket covers Paper parking Paper unparking Short se/f testLong se/f test Interface testAdjusting the Printing GAP International character set Print style and pitch selection Page Page OFF Control Panel OPERAllONS On Line switch Paper Feed switchQuiet Mode switch Sty/e/Pitch switchPOWER-UP Functions Sh0ff test paffern On Line switchLprint CHR$I Next B8 B9 Switch Combination Functions Switch combination functions of control panelTop Of fOff?L Style/Pitch Page Memo Using WE PR//vER Installing Your SoftwareCommand options PrinterSetting the DIP Switches Using Your SoftwareType sty/e and pitch selection Printercommands Memo Using the Printer with DOS and Basic HARD-COPYING the Screen MS-DOS and PC-DOSProgramming the Printer with DOS Commands Name of list device PRNNew file Programming the Printer with Basic Acopy LQELITE.DAT PRN Aprint README.DOC‘Cancel Lprint the Spacings are Changed Next H How the program works IBM Lprint ES= cHR$ocHR$6ocHR$6o Cleaning the Printer Replacing the RibbonReplacing the Print Head Replacing the ribbon cartrlctgeConnector cover Fligure 5-2. Replacing the print head Replacing the Battery in the RAM Card If a// text is printed on the same line TroubleshootingIf printing is faint, incomplete, or unclear If line spacing is twice as wide as expectedIf you have problems with download characters If you have problems with graphicsIf you have problems with horizontal tabulation Printing Mechanism Switches and fndicatorsInterface and Emulation Character Sets Dot Matrix SizeDimensions and Weight Paper SpecificationsType Sty/es and Pitches Environmental Requirements Electrical SpecificationsInterface Signals OptionSignal Pin No Name Memo Font Control Commands Select draft quality charactersSelect ornament character Select LQ charactersSelect LQ type Style Select Italic CharactersDouble-strike Printing Select Upright CharactersStart Underlining Start Overlining Cancel Superscript Or subscriptStop Underlining Stop OverliningSelect character set #7 Select Standard characterSelect IBM character set Select Character set #2Select s/ash zero Enable printing of all character codesEnable printing of a// character codes on next character Select normal zeroHigh-speed elite pitch Pica pitchElite pitch High-density elite pitchCondensed printing Cancel condensed printingCancel expanded printing Expanded printingSe/ect proportional spacing Select master print modeCaucel one-line expanded printing Select fixed spacingPrint double-height characters Increase character SpacingSelect double or quadruple size Return to normal HeightSelect Character Width Select character height, width, and line spacingSet line spacing to 7160 or 7172 inch Vertical Position CommandsSelect character type and print pitch Set line spacing to 718 inchSet line spacing to n/780 or n/216 inch Set line spacing to 716 inchSet base unit for line spacing Set line spacing to n/360 inchDefine line spacing to n/72 inch Select forward feed modeSelect reverse feed mode Execute ESC aFeed paper n lines Perform one n/180-inch or n/2164nch line feedPerform one n/780-inch reverse line feed Set top of page at current positionSet top margin Cancel top and bottom marginsSet page length to n inches Set bottom marginSet vertical tab stops Disable paper-out detectorEnable paper-out detector Set vertical tab stops every n linesSet left margin Select Vertical Tab channelVertical tab Set right marginCarriage return Cancel automatic line feedSet left and right margins Set automatic Line feedCenter text BackspaceLeff justify Right justifySet horizontal tab stop every n columns Reset all tab stopsSet horizontal tab stops Horizontal tabAbsolute horizontal tab in inches Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in columnsPrint 8-bit double-density graphics Graphics CommandsPrint 8-bit single-density graphics Print 8-bit double-density, double-speed graphicsSelect graphics mode Print M-bit hex-density graphicsCopy standard characters from ROM into RAM Convert graphics densityDownload Character Define Download Select download character setROM Other Printer Control CommandsDelete Last character Sent MSBQuiet Print Cancel Quiet PrintRepeat data Last LineSet printer on-line Cancel Immediate PrintSet printer off-line Stop printingOne-line unidirectional printing PrintingUnidirectional printing Manual feedEject Paper Reset printerSet print start position on ASF Memo AppendixCDOWNLOAD Norma/ characterSemi-condensed Proportional Super/subscript character Iiao 1600 2440 If ST=5 then CLS Goto 3480 Character Sets I7’ Standard Character SETPj-iii-j IBM Character SET #2 Page IBM CH Aracter SET #I Additional Character SET International Character Sets SfRIndex Lol 111107 Command Summary ESC ESC p ESC p0 ESC p.‘ 111