Star Micronics NX-2400 user manual Top Of fOff?L Style/Pitch

Page 34

I

1

I

I

Page feed: Paper Feed and On Line switches

If you are using single sheets, this operation ejects the current page. If you are using fanfold forms, it feeds to the top of the next page.

1.Press the On Line switch to set the printer off-line.

2.Press the Paper Feed switch and hold it down. The printer will start

performing successive line feeds.

3.Still holding the Paper Feed switch down, press the On Line switch, then release both switches. The printer will smoothly eject the current page.

Top Of fOff?L Style/Pitch

and

Paper

Feed

switches

 

 

 

-.

When you turn on printer

 

power,

the

top-of-form

position

is auto-

 

 

matically set to the current

position. If this

is not

where

you want

the top

-

-

of the page to be, you can

change

the

top-of-form

position as follows.

 

 

1.Press the On Line switch to set the printer off-line.

2.Move the paper to the desired top-of-form position by pressing the Paper

Feed switch, or by performing a forward or reverse micro-feed.

3.Press the Style/Pitch switch and hold it down.

4.Press the Paper Feed switch. The printer will beep to indicate that the

top-of-form position has been set.

Forward micro-feed:On Line and Paper Feed switches

For fine alignment, you can feed the paper forward in very small in- crements as follows:

1.Press the On Line switch to set the printer off-line.

2. Press the On Line switch again and hold it down.

-

3.Press the Paper Feed switch. The paper will start advancing in a series of small steps. When you want to stop, release both switches.

Reverse micro-feed:On Line and Quiet Mode switches

-

You can also feed the paper in small increments in reverse, to return

to a higher position on the same page.

-

Note: With fanfold forms, do not try to return to a previous page. The

perforation may catch inside the printer.

-

1. Press the On Line switch to set the printer off-line.

2. Press the On Line switch again and hold it down,

-

3. Press the Quiet Mode switch. The paper will start moving backwards in a series of small steps. When you want to stop, release both switches.

-

26

Page 33 Page 35
Image 34
Page 33 Page 35
Contents NX-2400 Page HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents With DOS and Basic Download Character Generator Chapter Platen Setting UP Remove the top coverInstall the ribbon cartridge Install the optional IC card Replace the top cowerConnect the printer to the computer Mount the paper guideSemiautomatic loading Figure l-7.Mounting the paper guide for single sheetsManual loading Loading and Parking Fanfold Forms 11. Closing the sprocket covers Paper parking Paper unparking Short se/f testLong se/f test Interface testAdjusting the Printing GAP International character set Print style and pitch selection Page Page OFF Control Panel OPERAllONS On Line switch Paper Feed switchQuiet Mode switch Sty/e/Pitch switchPOWER-UP Functions Sh0ff test paffern On Line switchLprint CHR$I Next B8 B9 Switch Combination Functions Switch combination functions of control panelTop Of fOff?L Style/Pitch Page Memo Using WE PR//vER Installing Your SoftwareCommand options PrinterSetting the DIP Switches Using Your SoftwareType sty/e and pitch selection Printercommands Memo Using the Printer with DOS and Basic HARD-COPYING the Screen MS-DOS and PC-DOSProgramming the Printer with DOS Commands Name of list device PRNNew file Programming the Printer with Basic Acopy LQELITE.DAT PRN Aprint README.DOC‘Cancel Lprint the Spacings are Changed Next H How the program works IBM Lprint ES= cHR$ocHR$6ocHR$6o Cleaning the Printer Replacing the RibbonReplacing the Print Head Replacing the ribbon cartrlctgeConnector cover Fligure 5-2. Replacing the print head Replacing the Battery in the RAM Card If a// text is printed on the same line TroubleshootingIf printing is faint, incomplete, or unclear If line spacing is twice as wide as expectedIf you have problems with download characters If you have problems with graphicsIf you have problems with horizontal tabulation Printing Mechanism Switches and fndicatorsInterface and Emulation Character Sets Dot Matrix SizeDimensions and Weight Paper SpecificationsType Sty/es and Pitches Environmental Requirements Electrical SpecificationsInterface Signals OptionSignal Pin No Name Memo Font Control Commands Select draft quality charactersSelect ornament character Select LQ charactersSelect LQ type Style Select Italic CharactersDouble-strike Printing Select Upright CharactersStart Underlining Start Overlining Cancel Superscript Or subscriptStop Underlining Stop OverliningSelect character set #7 Select Standard characterSelect IBM character set Select Character set #2Select s/ash zero Enable printing of all character codesEnable printing of a// character codes on next character Select normal zeroHigh-speed elite pitch Pica pitchElite pitch High-density elite pitchCondensed printing Cancel condensed printingCancel expanded printing Expanded printingSe/ect proportional spacing Select master print modeCaucel one-line expanded printing Select fixed spacingPrint double-height characters Increase character SpacingSelect double or quadruple size Return to normal HeightSelect Character Width Select character height, width, and line spacingSet line spacing to 7160 or 7172 inch Vertical Position CommandsSelect character type and print pitch Set line spacing to 718 inchSet line spacing to n/780 or n/216 inch Set line spacing to 716 inchSet base unit for line spacing Set line spacing to n/360 inchDefine line spacing to n/72 inch Select forward feed modeSelect reverse feed mode Execute ESC aFeed paper n lines Perform one n/180-inch or n/2164nch line feedPerform one n/780-inch reverse line feed Set top of page at current positionSet top margin Cancel top and bottom marginsSet page length to n inches Set bottom marginSet vertical tab stops Disable paper-out detectorEnable paper-out detector Set vertical tab stops every n linesSet left margin Select Vertical Tab channelVertical tab Set right marginCarriage return Cancel automatic line feedSet left and right margins Set automatic Line feedCenter text BackspaceLeff justify Right justifySet horizontal tab stop every n columns Reset all tab stopsSet horizontal tab stops Horizontal tabAbsolute horizontal tab in inches Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in columnsPrint 8-bit double-density graphics Graphics CommandsPrint 8-bit single-density graphics Print 8-bit double-density, double-speed graphicsSelect graphics mode Print M-bit hex-density graphicsCopy standard characters from ROM into RAM Convert graphics densityDownload Character Define Download Select download character setROM Other Printer Control CommandsDelete Last character Sent MSBQuiet Print Cancel Quiet PrintRepeat data Last LineSet printer on-line Cancel Immediate PrintSet printer off-line Stop printingOne-line unidirectional printing PrintingUnidirectional printing Manual feedEject Paper Reset printerSet print start position on ASF Memo AppendixCDOWNLOAD Norma/ characterSemi-condensed Proportional Super/subscript character Iiao 1600 2440 If ST=5 then CLS Goto 3480 Character Sets I7’ Standard Character SETPj-iii-j IBM Character SET #2 Page IBM CH Aracter SET #I Additional Character SET International Character Sets SfRIndex Lol 111107 Command Summary ESC ESC p ESC p0 ESC p.‘ 111
Top Page Image Contents