Fujitsu ST5111, ST5112 manual FCC Regulatory Information

Page 61

FCC REGULATORY INFORMATION

Please note the following regulatory information related to the optional wireless LAN module.

Regulatory Notes and Statements

Wireless LAN, Health and Authorization for use

Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:

■On board an airplane, or

■In an explosive environment, or

■In situations where the interference risk to other devices or ser- vices is perceived or identified as harmful.

In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chem- ical/oil/gas industrial plants, private buildings), obtain authoriza- tion to use these devices prior to operating the equipment.

Regulatory Information/Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documenta- tion provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufac- turer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interfer- ence caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsi- bility of the user to correct any interference caused by such unau- thorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines.

This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Federal Communications Commission statement

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

W i r e l e s s L A N U s e r ’ s G u i d e

1.Reorient or relocate the receiving antenna.

2.Increase the distance between the equipment and the receiver.

3.Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.

4.Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure statement

The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by addi- tional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.

The maximum SAR values measured from the devices are:

■Intel PROSet Wireless LAN (WM3945ABG): 1.47 W/kg

■Atheros Wireless LAN (AR5BX6): 1.57 W/kg

■Intel PROSet Wireless LAN (WM3945ABG) + Bluetooth Simultaneous: 1.47 W/kg

■Atheros Wireless LAN (AR5BX6) + Bluetooth Simultaneous:

1.56W/kg

Export restrictions

This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly autho- rized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.

Canadian Notice

The device for the 5150-5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems.

The maximum antenna gain of 6 dBi permitted (for devices in the 5250-5350 MHz, 5470-5725, and 5475-5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210.

In addition, users should also be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.

53

Page 60 Page 62
Image 61
Page 60 Page 62
Contents User’s Guide Page OmniPass is a trademark of Softex, Inc Copyright and Trademark InformationAC Adapter output polarity Important Safety InstructionsFor Authorized Repair Technicians Only System DisposalTable of Contents Appendix B Security Device USER’S Guide Preface Page Preface Limited Warranty InformationAbout this Guide Fujitsu Contact InformationPage Getting Started with Your Tablet PC Page Getting Started with Your Stylistic Tablet PC Optional AccessoriesInfrared keyboard/mouse ports The infrared ports Stylistic Tablet PC FeaturesBack Features Top Features Left-Side Features Right-Side Features Icon Mode/State LED State Remarks Status DisplaySystem Status Indicators Application Buttons Tablet Button Settings Control Panel -Tablet Button SettingsMenu UtilityNavigation Buttons Navigation ButtonsSame as if you had tapped F2 on a keyboard Tertiary Functions of Application and Navigation ButtonsPasswords Setting UP the Security PanelSecurity Functions of Application Buttons Using Your Security Panel PrecautionsUninstalling the Security Panel Application Reinstalling the Security Panel Application Fujitsu Driver Update UtilityRecommend that you install the ClickMe! utility the first UserConnector Tablet PC Purpose Peripheral Connectors and Peripheral InterfacesPeripheral Connectors/Interfaces Page Using Your Stylistic Tablet PC Page System States Using the Stylistic ST5100 Series Tablet PCBooting the System the First Time Powering UP the Tablet PCStarting Windows Vista the first time Registering Windows Vista with MicrosoftSuspending System Operation Shutting Down the SystemRegistering Your Stylistic Tablet PC with Fujitsu Registering Windows XP with MicrosoftPower icon is not displayed Hibernate mode Power icon is blinking Standby modeFrom Standby mode From Hibernate modeAdjusting the Display Brightness Using the Shock Sensor UtilityTip Switch Pen Tether Attachment Point Using the PENCharging the Battery Installing a PEN TetherCalibrating the PEN Replacing the PEN TIPTips for Conserving Battery Power Removing and Installing the BatteryBattery uses Lithium ion battery cells which have Operation of the Bridge BatteryMemory STICK/SD Card Slot Modem ConnectionPC Card Slot Installing a Memory Module Removing and Installing MemoryTo install a Dimm module in the Tablet PC Removing a PC CardRemoving a Memory Module Installing a Dimm ModulePage Care and Maintenance Page Caring for Your Tablet PC Care and MaintenanceProtecting the Display Screen Avoiding Overheating Storing the Tablet PCTroubleshooting Cleaning the Display ScreenConfiguring Peripheral Interfaces Restoring the PRE-INSTALLED SoftwareRe-Installing Individual Drivers and Applications Boot Priority ChangeProcedure Automatically Downloading Driver UpdatesCheck for updates now About Fujitsu Driver UpdatePage System Specifications Page Processing Specifications Stylistic ST5100 Series Hardware SpecificationsPower Specifications FCC Notices Regulatory InformationAvis Aux Utilisateurs Du Réseau Téléphonique Canadien Appendix a Page FCC Regulatory Information Wireless LAN Devices Covered by this Document Before Using the Wireless LANCharacteristics of the Wlan Device Wireless LAN Modes Using this Wireless ModuleDeactivation using the wireless switch How to Handle This Wireless ModuleDeactivation using Windows Stopping TransmissionStarting Transmission Atheros Wireless LANConfiguring the Wlan With Windows Vista Connecting the WlanConfiguring the Wlan Using Windows XP Connecting to a Network with Windows VistaField Name Description Configuring Using Atheros Client Utility SoftwareSetting TCP/IP Setting the networkConnection to the Network Setting the Microsoft network-sharing service Setting the sharing functionSetting the file-sharing function Confirming the computer and work group namesConfirming connection Setting the printer-sharing functionConfirming the status of the radio Network Name SsidSecurity ModeSpeed Band FrequencyUnavailable TroubleshootingNetwork ConnectionCommunication Access pointIs disconnected Soon afterWireless LAN Glossary Shared key authentication Open system authenticationSsid Service Set Identifier Wi-FiIP address information Specifications SpecificationsWhat is BLUETOOTH? Using the Bluetooth DeviceWhere to Find Information about Bluetooth WarrantyPage Appendix B Page Installing the OmniPass Application Installing OmnipassIntroducing Fingerprint Sensor Device Getting StartedMaster Password Concept Uninstalling OmniPassUser Enrollment Verifying Information about OmniPassPassword Replacement Using OmnipassOmniPass Authentication Toolbar Basic EnrollmentLogging in to a Remembered Site Remembering a PasswordPassword Management Configuring OmnipassIdentities and Password Management OmniPass User IdentitiesExporting an OmniPass User Profile Omnipass Control CenterImporting an OmniPass User Profile Things to Know Regarding Import/ExportSystem Settings User SettingsCannot add a User with a Blank Password to OmniPass First option, Automatically log on to OmniPass asInstalling the TPM Applications Trusted Platform Module InstallationProcedure Enabling the Security Chip in BiosBattery power Adjusting the display brightness Air flow ventsIndex Setting up Security Panel Shock Sensor Utility Pen tether Peripheral connectorsStylistic ST5000 specifications Microphone jackWireless LAN/Bluetooth on/off switch USB ports Using the penTurning off the system Y l i s t i c S T 5 1 0 0 S e r i e s T a b l e t P C Page Page
Top Page Image Contents