Fujitsu ST4000P manual Powering UP the PEN Tablet PC, Shutting Down the System

Page 30

S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e – S e c t i o n T w o

Icon Appearance

Current State

To Change State*

Power icon

On State

To enter the Off state, shut down the system using the Start menu on your

or

system.

displayed

Idle State

 

To enter Suspend-to-RAM or Hibernate (Save-to-Disk)†state, suspend system

continuously

 

 

 

operation using either a hardware or software suspend.

 

 

 

Power icon blinking

Suspend-to-

To enter the On state, resume system operation by pressing the Suspend/

 

RAM†

Resume button.

 

 

To enter the Off state, resume system by pressing the Suspend/Resume

 

 

button, then shut down your system.

 

 

 

Power icon not

Off State, or,

To enter the On state, start your system, or resume system operation by

displayed

Hibernate

pressing the Suspend/Resume button.

 

(Save-to-Disk†)

 

Table 2-1 Changing System States

*Information in Table 2-1 on page 20 is supplied to help you understand which system states your system can enter from the current system state. Refer to the procedures on starting the system, shutting down the system, suspending system operation, and resuming system operation given later in this chapter.

†Your system may be configured to use either Suspend-to-RAM mode or Hibernate mode.

POWERING UP THE PEN TABLET PC

Follow the procedure below to start the Stylistic ST4000P Series pen tablet PC. Before you begin, confirm that the system is in the Off state. To do so, observe the Status display. If the Power icon is not visible in the Status display, the system is in Off state or in Hibernate (Save-to-Disk) mode and it is safe to perform this proce- dure. If the Power icon is visible (either blinking or on continuously), do not perform this procedure. See “System States” earlier in this chapter for details on modes represented by the Power icon.

1.Ensure that the battery in your pen tablet PC is sufficiently charged, or connect an external power source such as the AC adapter or auto adapter to your pen tablet PC.

2.Press the Power On/Suspend/Resume button to start the system.

After performing initialization, the system starts the operating system installed on the hard disk drive. Once the operating system is running, you can use the system.

SHUTTING DOWN THE SYSTEM

Follow these steps to shut down and turn off your system:

1.If system operation has been suspended, resume system operation. See “Resuming System Opera- tion” later in this chapter for details.

2.Save your work and close all running programs.

3.Choose Shut Down from the Windows (2000 Profes- sional or XP Professional) Start menu.

4.Carry out the Shut Down command.

The system is now in the Off state.

SUSPENDING SYSTEM OPERATION

The pen tablet PC allows you to suspend the system operation without closing programs or exiting the oper- ating system. Use this feature to conserve battery power when a system shutdown is not practical or when the battery needs to be changed.

P O I N T

If you have set your system to turn power off from the Power Options utility in the Control Panel, the following procedure will not be possible, since pressing the button shuts the system down rather than suspending it. To change your power options, go to Start -> Settings -> Control Panel -> Power Options.

20

Page 29 Page 31
Image 30
Page 29 Page 31
Contents According to FCC Part Fujitsu PC CorporationPage Table of Contents Page Preface Page Warranty Information About this GuideFujitsu Contact Information Page Getting Started with Your Pen Tablet PC Page Getting Started with Your Stylistic Pen Tablet PC IN-BOX Items for the Stylistic ST4000P Series PEN Tablet PCOptional Accessories Stylistic PEN Tablet PC Features Front FeaturesBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess ModeTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connectors and Peripheral Interfaces Connector Pen Tablet Purpose PeripheralPeripheral Connectors/Interfaces Page Using Your Stylistic ST4000P Series Pen Tablet PC Page Using the Stylistic ST4000P Series Pen Tablet PC System StatesSuspending System Operation Powering UP the PEN Tablet PCShutting Down the System Current State To Change StatePower icon is blinking Suspend-to-RAMmode Power icon is not displayed Hibernate modeU T I O N Resuming System Operation Using the PENInstalling a PEN Tether U T I O N SCalibrating the PEN Using Hovering ModeCharging the Battery To Calibrate the PenRemoving and Installing Battery Tips for Conserving Battery PowerI N T Removing and Installing Memory Modules Modem ConnectionPC Card Slot Installing a Memory Module Removing a Memory ModuleCare and Maintenance Page Care and Maintenance Protecting the Display ScreenStoring the PEN Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingSpeaker/Headphone Volume Too Low Configuring Peripheral InterfacesPen Tablet PC is Not Responding to the Pen Page Specifications Page Processing Specifications Stylistic ST4000P SpecificationsPhysical Specifications Memory/Storage SpecificationsAgency Approval Specifications Power SpecificationsEnvironmental Specifications Additional SpecificationsAgency Notices Page Regulatory Information FCC Registration NumberAvis Aux Utilisateurs Du Réseau Téléphonique Canadien E R T I S S E M E N TR N I N G S UL NoticeFor Authorized Repair Technicians Only System DisposalPage Appendix Page Federal Communications Commission statement FCC Regulatory InformationRegulatory Notes and Statements FCC Interference StatementWireless LAN Modes Using this Device Before Using this DeviceCharacteristics of the Device How to Handle This DeviceWhen you finish your entry, click Apply Connecting Windows 2000 SystemsSetting Parameters WorkflowEncryption Key Setup Network SettingsTCP/IP Settings Network Connection WindowsSetting File and Printer Sharing for Microsoft Networks Checking the full computer name and workgroupSharing Printer Sharing Accessing Another ComputerSharing Files Checking the ConnectionConnecting Windows XP Systems Checking connectivityNetwork Connection Network SettingsOn Wireless Network Connection Properties, click General Click OKSetting computer name and workgroup SharingTransfer data for send Tx and receive Troubleshooting Table You want to store the IP address Windows 2000 Click Start Programs AccessoriesWindows XP Click Start All Programs Accessories Click Enter, then go to the location you specified above.Problem Possible Cause WindowsAbout IP Addresses Problem Possible Cause Possible SolutionSetting IP Addresses Windows XPSpecifications Technical Specifications for Integrated Wireless LAN DevicePage Battery release button Battery release latch Battery gauge Battery gauge icon Battery icon Battery packBattery power External Monitor ConnectorOverheating, avoiding Save-to-Disk mode Peripheral connectorsPower On/Suspend/Resume Button Power usage Solving problems Speaker Speaker/headphone volume too lowWireless LAN module Wireless LAN On/Off switch Stylistic ST4000P SpecificationsSystem interface connector Network ConnectionY l i s t i c S T 4 0 0 0 P S e r i e s
Top Page Image Contents