Fujitsu ST4000P Storing the PEN Tablet PC, Avoiding Overheating, Cleaning the Display Screen

Page 40

S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e – S e c t i o n T h r e e

7.Clean any residue left behind by the protective coating from the exposed surface of the screen protector by wiping gently with a soft cotton cloth dampened with isopropyl alcohol. Wipe the screen protector with a soft dry cloth to remove any low- tack adhesive; this will help prevent the pen tip from squeaking.

The screen protector is now installed.

STORING THE PEN TABLET PC

Store the Stylistic ST4000P Series pen tablet PC in the Off state with a fully charged battery installed. You can store the pen tablet PC in the Off state for about 30 days with a fully charged battery installed. After this period, the battery should be recharged or replaced with a charged battery.

If you intend to store the pen tablet PC for a longer period of time, the small battery that maintains system time may need to be replaced. Replacement of the clock battery should only be performed by authorized techni- cians.

AVOIDING OVERHEATING

The pen tablet PC monitors its internal temperature. As the internal temperature approaches the tolerable limits of heat-sensitive components, system functions are automatically limited or turned off to prevent damage.

To avoid overheating the pen tablet PC, do not obstruct the air vents on the top and bottom edges of the pen tablet PC.

CLEANING THE DISPLAY SCREEN

To clean the pen tablet PC display screen, wipe the screen surface gently using a soft cotton cloth slightly dampened with water or isopropyl alcohol.

C A U T I O N

The Stylistic ST4000P Series pen tablet PC is not waterproof. Do not pour liquids on the pen tablet PC or wash the pen tablet PC with a heavily soaked cloth.

TROUBLESHOOTING

Solutions to some common problems are described in the following sections. If you are experiencing a problem with your pen tablet PC that you cannot solve by taking the actions described, contact your local help desk or your reseller for further assistance.

System Will Not Resume Operation

If the system will not resume operation after system operation has been suspended, check the following possible causes:

•The battery may either be defective, or discharged to a critically low level. When the battery reaches a critically low level, the system is forced into Suspend- to-RAM mode to avoid a total system power failure. To correct this problem, either connect an external power supply (such as the AC adapter), or install a charged battery in the pen tablet PC.

•The system may be at the critical thermal limit. To avoid damage to heat-sensitive components, the system enters Suspend-to-RAM mode when it gets too hot. System operation cannot be resumed until the pen tablet PC cools off to a tolerable temperature. Move the pen tablet PC to a cooler location.

Display Screen Blank or Difficult to Read

If the display screen on your pen tablet PC appears blank or is unreadable, confirm that the system is running (the Power icon is displayed continuously on the Status display), and check the following:

•The system brightness may be set too low, causing the screen to appear too dark. To change system brightness, press the Fn button twice to open the Fujitsu menu. Brightness can be adjusted from the menu.

•An external monitor may be selected. Press the Fn and Display Select buttons to determine whether the pen tablet PC display screen is selected.

•The video timeout may have expired. Tap on the display screen to reactivate the display. Note that this is a normal, power-saving feature.

Cursor Is Not Tracking Pen

If the cursor on the screen appears to be misaligned with the pen or is not accurately tracking the pen, calibrate the pen. See “To Calibrate the Pen” on page 23 for more information.

Infrared Data Transfer Is Not Working

If you are experiencing problems transferring data over the system’s infrared interface, note the following:

• Can the IrDA port on the pen tablet PC “see” the

30

Page 39 Page 41
Image 40
Page 39 Page 41
Contents According to FCC Part Fujitsu PC CorporationPage Table of Contents Page Preface Page About this Guide Warranty InformationFujitsu Contact Information Page Getting Started with Your Pen Tablet PC Page Getting Started with Your Stylistic Pen Tablet PC IN-BOX Items for the Stylistic ST4000P Series PEN Tablet PCOptional Accessories Stylistic PEN Tablet PC Features Front FeaturesBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess ModeTablet Button Settings Application ButtonsTablet Icon DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connectors and Peripheral Interfaces Connector Pen Tablet Purpose PeripheralPeripheral Connectors/Interfaces Page Using Your Stylistic ST4000P Series Pen Tablet PC Page Using the Stylistic ST4000P Series Pen Tablet PC System StatesPowering UP the PEN Tablet PC Shutting Down the SystemSuspending System Operation Current State To Change StatePower icon is not displayed Hibernate mode Power icon is blinking Suspend-to-RAMmodeU T I O N Using the PEN Installing a PEN TetherResuming System Operation U T I O N SUsing Hovering Mode Charging the BatteryCalibrating the PEN To Calibrate the PenTips for Conserving Battery Power Removing and Installing BatteryI N T Modem Connection Removing and Installing Memory ModulesPC Card Slot Installing a Memory Module Removing a Memory ModuleCare and Maintenance Page Care and Maintenance Protecting the Display ScreenCleaning the Display Screen TroubleshootingStoring the PEN Tablet PC Avoiding OverheatingConfiguring Peripheral Interfaces Speaker/Headphone Volume Too LowPen Tablet PC is Not Responding to the Pen Page Specifications Page Stylistic ST4000P Specifications Physical SpecificationsProcessing Specifications Memory/Storage SpecificationsPower Specifications Environmental SpecificationsAgency Approval Specifications Additional SpecificationsAgency Notices Page Regulatory Information FCC Registration NumberAvis Aux Utilisateurs Du Réseau Téléphonique Canadien E R T I S S E M E N TUL Notice For Authorized Repair Technicians OnlyR N I N G S System DisposalPage Appendix Page FCC Regulatory Information Regulatory Notes and StatementsFederal Communications Commission statement FCC Interference StatementBefore Using this Device Characteristics of the DeviceWireless LAN Modes Using this Device How to Handle This DeviceConnecting Windows 2000 Systems Setting ParametersWhen you finish your entry, click Apply WorkflowNetwork Settings TCP/IP SettingsEncryption Key Setup Network Connection WindowsChecking the full computer name and workgroup Setting File and Printer Sharing for Microsoft NetworksSharing Accessing Another Computer Sharing FilesPrinter Sharing Checking the ConnectionConnecting Windows XP Systems Checking connectivityNetwork Settings On Wireless Network Connection Properties, click GeneralNetwork Connection Click OKSetting computer name and workgroup SharingTransfer data for send Tx and receive Troubleshooting Table Windows 2000 Click Start Programs Accessories Windows XP Click Start All Programs AccessoriesYou want to store the IP address Click Enter, then go to the location you specified above.Problem Possible Cause WindowsProblem Possible Cause Possible Solution Setting IP AddressesAbout IP Addresses Windows XPSpecifications Technical Specifications for Integrated Wireless LAN DevicePage Battery gauge Battery gauge icon Battery icon Battery pack Battery powerBattery release button Battery release latch External Monitor ConnectorPeripheral connectors Power On/Suspend/Resume Button Power usageOverheating, avoiding Save-to-Disk mode Solving problems Speaker Speaker/headphone volume too lowStylistic ST4000P Specifications System interface connectorWireless LAN module Wireless LAN On/Off switch Network ConnectionY l i s t i c S T 4 0 0 0 P S e r i e s
Top Page Image Contents