Fujitsu ST4000P manual Removing and Installing Battery, Tips for Conserving Battery Power, I N T

Page 34

S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e – S e c t i o n T w o

Battery Charge

Approximate

Approximate

Charge Time

Charge Time

Level Reached

(not in use)

(in use)

 

 

 

 

90%

3.5 hours

7 hours*

 

 

 

100%

4.5 hours

8 hours*

 

 

 

Table 2-2 Battery Charging Time

* Depends upon the applications in use.

Also note the following with respect to charging the battery:

•You can use the system, suspend system operation, or shut down and turn off the system without interrupting the charging process; however, using the system while the battery is charging will cause the battery to charge at a slower rate, as noted in Table 2- 2, “Battery Charging Time".

•As noted in the procedure above, the system will not begin charging the battery if the battery charge level is 90% or higher when the system is initially connected to external DC power. (This prevents the battery from being overcharged.)

•The Stylistic ST4000P Series battery uses Lithium ion battery cells which have no “memory effect.” You do not need to discharge the battery before you begin charging.

REMOVING AND INSTALLING

THE BATTERY

The battery can be removed from the pen tablet PC and swapped with a charged battery. The battery can then be charged in an external charger if one is available. To remove the battery from the pen tablet PC:

1.Choose one of the following:

•If a charged battery is available, you can suspend system operation. A built-in “bridge” battery will maintain the system in Suspend-to-RAM mode for about 5 minutes while the battery is removed; this allows time for replacement with a charged battery.

•If a charged battery is not available, save your work and close all running programs, then shut down the system or Hibernate (Save-to-Disk).

•Plug in an external DC power source.

2.Slide the battery release latch in the direction indicated. (See Figure 1 on page 24 for location).

3.Pull the battery away from the system, as shown in the illustration and remove the battery from the pen tablet PC.

If you are using an external battery charger, refer to the instructions provided with the battery charger.

P O I N T

Under Federal, state, or local law, it may be illegal to dispose of batteries by putting them in the trash. Be sure to dispose of batteries in accordance with local government regulations.

To install the battery:

1.Orient the battery with the slides in the empty battery tray. Slide the battery into the tray and press it firmly until it is seated. When it is properly seated, the battery release latch should return to position and lock the battery.

Figure 2-2 Removing the Battery

Once the battery is installed, you can resume system operation or start and use your system normally.

TIPS FOR CONSERVING BATTERY POWER

You can extend the charge life of your battery by conserving battery power. (Your results may vary depending on your application and how the system is configured.) Here are some suggestions to help you conserve battery power:

•Use an external power source such as the AC adapter whenever the system is docked.

•Suspend system operation if you know that you won’t be using the system for a while.

•Shut down the system if you won’t be using the system for an extended period of time.

•Use power management (available on the desktop) to help you conserve power automatically.

•Battery life is dependent upon the operating system, power settings, and applications in use.

24

Page 33 Page 35
Image 34
Page 33 Page 35
Contents According to FCC Part Fujitsu PC CorporationPage Table of Contents Page Preface Page About this Guide Warranty InformationFujitsu Contact Information Page Getting Started with Your Pen Tablet PC Page Getting Started with Your Stylistic Pen Tablet PC IN-BOX Items for the Stylistic ST4000P Series PEN Tablet PCOptional Accessories Stylistic PEN Tablet PC Features Front FeaturesBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess ModeTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connectors and Peripheral Interfaces Connector Pen Tablet Purpose PeripheralPeripheral Connectors/Interfaces Page Using Your Stylistic ST4000P Series Pen Tablet PC Page Using the Stylistic ST4000P Series Pen Tablet PC System StatesSuspending System Operation Powering UP the PEN Tablet PCShutting Down the System Current State To Change StatePower icon is not displayed Hibernate mode Power icon is blinking Suspend-to-RAMmodeU T I O N Resuming System Operation Using the PENInstalling a PEN Tether U T I O N SCalibrating the PEN Using Hovering ModeCharging the Battery To Calibrate the PenTips for Conserving Battery Power Removing and Installing BatteryI N T Modem Connection Removing and Installing Memory ModulesPC Card Slot Installing a Memory Module Removing a Memory ModuleCare and Maintenance Page Care and Maintenance Protecting the Display ScreenStoring the PEN Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingConfiguring Peripheral Interfaces Speaker/Headphone Volume Too LowPen Tablet PC is Not Responding to the Pen Page Specifications Page Processing Specifications Stylistic ST4000P SpecificationsPhysical Specifications Memory/Storage SpecificationsAgency Approval Specifications Power SpecificationsEnvironmental Specifications Additional SpecificationsAgency Notices Page Regulatory Information FCC Registration NumberAvis Aux Utilisateurs Du Réseau Téléphonique Canadien E R T I S S E M E N TR N I N G S UL NoticeFor Authorized Repair Technicians Only System DisposalPage Appendix Page Federal Communications Commission statement FCC Regulatory InformationRegulatory Notes and Statements FCC Interference StatementWireless LAN Modes Using this Device Before Using this DeviceCharacteristics of the Device How to Handle This DeviceWhen you finish your entry, click Apply Connecting Windows 2000 SystemsSetting Parameters WorkflowEncryption Key Setup Network SettingsTCP/IP Settings Network Connection WindowsChecking the full computer name and workgroup Setting File and Printer Sharing for Microsoft NetworksSharing Printer Sharing Accessing Another ComputerSharing Files Checking the ConnectionConnecting Windows XP Systems Checking connectivityNetwork Connection Network SettingsOn Wireless Network Connection Properties, click General Click OKSetting computer name and workgroup SharingTransfer data for send Tx and receive Troubleshooting Table You want to store the IP address Windows 2000 Click Start Programs AccessoriesWindows XP Click Start All Programs Accessories Click Enter, then go to the location you specified above.Problem Possible Cause WindowsAbout IP Addresses Problem Possible Cause Possible SolutionSetting IP Addresses Windows XPSpecifications Technical Specifications for Integrated Wireless LAN DevicePage Battery release button Battery release latch Battery gauge Battery gauge icon Battery icon Battery packBattery power External Monitor ConnectorOverheating, avoiding Save-to-Disk mode Peripheral connectorsPower On/Suspend/Resume Button Power usage Solving problems Speaker Speaker/headphone volume too lowWireless LAN module Wireless LAN On/Off switch Stylistic ST4000P SpecificationsSystem interface connector Network ConnectionY l i s t i c S T 4 0 0 0 P S e r i e s
Top Page Image Contents