Fujitsu ST4000P Windows 2000 Click Start Programs Accessories, You want to store the IP address

Page 66

S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e – A p p e n d i x

Problem

Possible Cause

 

 

Possible Solution

 

 

 

 

 

 

IP packet isn’t

Run the PING

Perform the following steps to run the PING command to check if the

reaching its

command to check

IP packet is correctly delivered to the destination.

destination

the connection

To run the PING command, the TCP/IP protocol must be installed.

 

 

 

 

First you will determine your IP address, then you will make sure your

 

 

IP address can respond, and then you will make sure other computers

 

 

can be addressed.

 

 

1.

Windows 2000: Click [Start] -> [Programs] -> [Accessories] -

 

 

 

 

> [Command Prompt].

 

 

Windows XP: Click [Start] -> [All Programs] -> [Accessories] ->

 

 

 

 

[Command Prompt].

 

 

2.

Type: ipconfig > directory\filename

 

 

 

 

where directory and filename represent the location at which

 

 

 

 

you want to store the IP address.

 

 

3. Click [Enter], then go to the location you specified above. The

 

 

 

 

IP address for your system will be contained in the file.

 

 

4. To check that your IP address is functioning properly, go back

 

 

 

 

to the DOS prompt and type: ping <IP address>, then press

 

 

 

 

[Enter]. You will receive several replies, followed by the PING

 

 

 

 

statistics (similar to below).

 

 

5. To check that your system is communicating with other

 

 

 

 

systems, go to the DOS prompt and type:

 

 

 

 

\>ping XXX.XXX.XXX.XXX. (With the destination IP address

 

 

 

 

in place of XXX.XXX.XXX.XXX).

 

 

Example: if the destination IP address is 10.0.1.3:

 

 

C:\>ping 10.0.1.3

 

 

A message similar to the following appears if the connection is

 

 

successful.

 

 

Pinging 10.0.1.3 with 32 bytes of data:

 

 

Reply from 10.0.1.3: bytes=32 time=1ms TTL=32

 

 

Reply from 10.0.1.3: bytes=32 time<10ms TTL=32

 

 

Reply from 10.0.1.3: bytes=32 time=4ms TTL=32

 

 

Reply from 10.0.1.3: bytes=32 time<10ms TTL=32

 

 

If the connection fails, [Request timed out], [Destination host

 

 

unreachable], or a similar message appears. In this case, refer to the

 

 

“Other computers are not displayed” portion of this chapter.

 

 

 

Cannot connect to

There are several

The following causes are possible. Check each one of them.

the network

possible causes, as

 

The network name or encryption key is not right.

 

listed to the right.

 

 

 

The driver has not correctly started.

 

Refer to the

 

 

 

The destination computer is not turned on.

 

specific section of this

 

 

 

You do not have the access privilege to the destination computer.

 

manual or your user’s

 

 

 

The card has failed.

 

manual.

 

 

 

Hardware conflict.

 

 

 

 

 

 

 

 

56

Image 66
Contents According to FCC Part Fujitsu PC CorporationPage Table of Contents Page Preface Page Warranty Information About this GuideFujitsu Contact Information Page Getting Started with Your Pen Tablet PC Page Getting Started with Your Stylistic Pen Tablet PC IN-BOX Items for the Stylistic ST4000P Series PEN Tablet PCOptional Accessories Stylistic PEN Tablet PC Features Front FeaturesBack Features Top Features Left-Side Features Right-Side Features Status Display Icon Mode/State LED State RemarksAccess ModeTablet Icon Tablet Button SettingsApplication Buttons DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connectors and Peripheral Interfaces Connector Pen Tablet Purpose PeripheralPeripheral Connectors/Interfaces Page Using Your Stylistic ST4000P Series Pen Tablet PC Page Using the Stylistic ST4000P Series Pen Tablet PC System StatesSuspending System Operation Powering UP the PEN Tablet PCShutting Down the System Current State To Change StatePower icon is blinking Suspend-to-RAMmode Power icon is not displayed Hibernate modeU T I O N Resuming System Operation Using the PENInstalling a PEN Tether U T I O N SCalibrating the PEN Using Hovering ModeCharging the Battery To Calibrate the PenRemoving and Installing Battery Tips for Conserving Battery PowerI N T Removing and Installing Memory Modules Modem ConnectionPC Card Slot Installing a Memory Module Removing a Memory ModuleCare and Maintenance Page Care and Maintenance Protecting the Display ScreenStoring the PEN Tablet PC Cleaning the Display ScreenTroubleshooting Avoiding OverheatingSpeaker/Headphone Volume Too Low Configuring Peripheral InterfacesPen Tablet PC is Not Responding to the Pen Page Specifications Page Processing Specifications Stylistic ST4000P SpecificationsPhysical Specifications Memory/Storage SpecificationsAgency Approval Specifications Power SpecificationsEnvironmental Specifications Additional SpecificationsAgency Notices Page Regulatory Information FCC Registration NumberAvis Aux Utilisateurs Du Réseau Téléphonique Canadien E R T I S S E M E N TR N I N G S UL NoticeFor Authorized Repair Technicians Only System DisposalPage Appendix Page Federal Communications Commission statement FCC Regulatory InformationRegulatory Notes and Statements FCC Interference StatementWireless LAN Modes Using this Device Before Using this DeviceCharacteristics of the Device How to Handle This DeviceWhen you finish your entry, click Apply Connecting Windows 2000 SystemsSetting Parameters WorkflowEncryption Key Setup Network SettingsTCP/IP Settings Network Connection WindowsSetting File and Printer Sharing for Microsoft Networks Checking the full computer name and workgroupSharing Printer Sharing Accessing Another ComputerSharing Files Checking the ConnectionConnecting Windows XP Systems Checking connectivityNetwork Connection Network SettingsOn Wireless Network Connection Properties, click General Click OKSetting computer name and workgroup SharingTransfer data for send Tx and receive Troubleshooting Table You want to store the IP address Windows 2000 Click Start Programs AccessoriesWindows XP Click Start All Programs Accessories Click Enter, then go to the location you specified above.Problem Possible Cause WindowsAbout IP Addresses Problem Possible Cause Possible SolutionSetting IP Addresses Windows XPSpecifications Technical Specifications for Integrated Wireless LAN DevicePage Battery release button Battery release latch Battery gauge Battery gauge icon Battery icon Battery packBattery power External Monitor ConnectorOverheating, avoiding Save-to-Disk mode Peripheral connectorsPower On/Suspend/Resume Button Power usage Solving problems Speaker Speaker/headphone volume too lowWireless LAN module Wireless LAN On/Off switch Stylistic ST4000P SpecificationsSystem interface connector Network ConnectionY l i s t i c S T 4 0 0 0 P S e r i e s