Fujitsu D1561, D1562 technical manual Important notes, Information about boards

Page 12

Important notes

Important notes

With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system.

Connecting cables for peripherals must be adequately shielded to avoid interference.

!

i

Observe the safety notes in the operating manual of your system.

Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules / Upgrading" - "Replacing the lithium battery" section.

Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. There is a danger of burns!

The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility".

Compliance was tested in a typical PC configuration.

When installing the board, refer to the specific installation information in the manual for the receiving device.

The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre.

Information about boards

To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts.

Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage.

Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the mainboard or components on it, for example memory modules or processors.

Never use sharp objects (screwdrivers) for leverage.

Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.

When you handle boards fitted with ESDs, you must, under all circumstances, observe the following:

You must always discharge static build up (e.g. by touching a grounded object) before working.

The equipment and tools you use must be free of static charges.

Remove the power plug from the mains supply before inserting or removing boards containing ESDs.

Always hold boards with ESDs by their edges.

Never touch pins or conductors on boards fitted with ESDs.

2 - English

A26361-D1562-Z120-2-6319

Image 12
Contents Mainboard D1562/D1561 Sie haben Page A26361-D1562-Z120-1-6319 Mainboard D1562/D1561 Français Technisches Handbuch Technical ManualAusgabe Mai 2003 May 2003 edition Page Page Übersicht/Overview Mainboard D1562/61 = USB G/HContents Page Mainboard D1562/D1561 Notational conventionsAdditional information Important notes Information about boardsList of features Onboard featuresInternal ports Special features Harddisk Password and Harddisk Silent ModeExternal ports Thermal Management and System MonitoringLogo Boot DeskView / DeskViewOEM Recovery BiosBrief instructions on installing mainboard Prior to installationInstallation Driver installation Brief instructions on installing mainboardInterfaces and connectors LAN connectorExternal ports Internal ports and connectors Graphics port Supported screen resolutionsHard disk connection Audio front panelPower On LED Pin assignment of internal portsFront panel Serial ATA internalATA interface IRQ high assertedAudio S/PDIF CD audio inputAUX audio Stromversorgungsüberwachung / Power supply control Audio front panelUSB E/F dual channel Dual channelSerial port FanPower supply ATX Additional power supply ATX12Settings with switches and jumpers Recovering System Bios switch 2 / pin pairReserved switch 3 and switch 4 if present Removing and installing processors Technical dataAdd-on modules / Upgrading Replacing processorMounting heat sink Upgrading main memory Memory clock pulse speedSystem bus MHz DDR400 MHz DDR333 MHz DDR266 MHz Installing a memory module Removing a memory moduleUpgrading AGP screen controllers Adding PCI cardsPCI bus interrupts Selecting correct PCI slot Monofunctional expansions cardsInterrupt Line Onboard controller USB 1,1 USB 2,0 SMBusAC97 Audio ModemReplacing the lithium battery Bios update Bios Recovery Recovering System BiosWhen should a Bios update be carried out? Bios update under Windows with DeskFlash utilityMicrocode Update What is a microcode update?When should a microcode update be carried out? Drivers DriversAnnex Electrical PropertiesLoadability for connections and fuses Mainboard current requirementAPM and Acpi system status, energy-saving modes LEDMainboard Revision and Bios Version Bios versionMainboard Revision Error messages FlashbioË/p6 ÚError messages Missing or invalid Nvram token System battery is dead Replace and run Setup Glossary