IBM manual XSeries 445 Type 8870 User’s Guide

Page 76

where other Remote Supervisor Adapters, ASM processors, and ASM PCI Adapters on the network reside. Second, the ASM interconnect network enables other interconnect network devices to use the resources (Ethernet or modem) of other Remote Supervisor Adapters, ASM processors, and ASM PCI Adapters in the ASM interconnect network for sending alerts. This interconnect network is used when Remote Supervisor Adapters, ASM processors, or ASM PCI Adapters cannot send an alert and must forward the information to another one of these devices to send the alert.

Planning and cabling the interconnect network: To support the most recent ASM features, a Remote Supervisor Adapter must be the main gateway interconnect to the ASM interconnect bus if the bus also includes servers with ASM PCI adapters or ASM processors. The Remote Supervisor Adapter forwards the ASM information generated by the servers attached to the ASM interconnect bus to other servers on the Ethernet network. The connected ASM processors and ASM PCI Adapters are managed through the new user interface and Web browser access of the Remote Supervisor Adapter.

Note: To ensure the stability of the system, you must have the most current level of firmware installed on the Remote Supervisor Adapter that is the main interconnect gateway for the ASM interconnect network. The most current level of firmware is available on the World Wide Web at http://www.ibm.com/pc/support/. For more information on updating firmware, see the IBM Remote Supervisor Adapter User’s Guide on the IBM xSeries Documentation CD.

You must connect an ASM Interconnect module to the Remote Supervisor Adapter and to each xSeries 445 server that you connect to the ASM interconnect network bus.

Attention: To avoid damage to the Ethernet connector on the Remote Supervisor Adapter, do not connect the ASM Interconnect module to the Remote Supervisor Adapter Ethernet port.

To connect the servers, note the following setup and configuration considerations:

vMake sure that the ASM interconnect network is set up as a bus, not as a ring. You must connect the servers to the ASM interconnect network in a series, with terminated beginning and end points.

vMake sure that the total combined length of all Ethernet cables connecting the server in the ASM interconnect network does not exceed 91 M (300 ft).

vEach Remote Supervisor Adapter, ASM PCI adapter, or ASM processor that is connected to the ASM interconnect network bus counts as one connection. For example, if an ASM PCI adapter is installed in a server that has an ASM processor, the processor and the adapter connect to each other using one ASM interconnect connection, but the processor and the adapter count as two connections on the ASM interconnect network bus.

Forwarding alerts: Remote Supervisor Adapters, ASM PCI adapters, and ASM processors that are connected to an ASM interconnect network share resources and system-management information. This section provides information on how alerts are forwarded in the ASM interconnect network.

During normal operation, each Remote Supervisor Adapter, ASM processor, or ASM PCI adapter on the ASM interconnect network communicates with the other processors and adapters on the network. Processors or adapters that have a modem or Ethernet connection notify the other processors and adapters that these

64xSeries 445 Type 8870: User’s Guide

Page 75 Page 77
Image 76
Page 75 Page 77
Contents ERserver Page ERserver Page Contents Iv xSeries 445 Type 8870 User’s Guide Safety To Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb 82 kg 180 lb XSeries 445 Type 8870 User’s Guide Introducing the IBM xSeries 445 server Related documentationLearn section, click Online publications Click ContinueFeatures and specifications MicroprocessorWhat your server offers Light path diagnostics feature Redundant cooling and power capabilitiesLarge data-storage capacity and hot-swap capability Redundant connectionReliability, availability, and serviceability features UpdateXpress program Active MemoryMemory scrubbing and Memory ProteXion Memory mirroringIBM Director IBM Universal ManageabilityServer controls, LEDs, and power Front viewXSeries 445 Type 8870 User’s Guide Rear view Rear view of model with Remote Supervisor Adapter II-EXARemote Supervisor Adapter II-EXA connectors and LEDs Introducing the IBM xSeries 445 server Server power features Turning on the serverTurning off the server XSeries 445 Type 8870 User’s Guide Configuration/Setup Utility program Configuring scalable partitionsEthernet controller configuration Integrated System Management Processor Update programUsing the Configuration/Setup Utility program Starting the Configuration/Setup Utility programConfiguration/Setup Utility menu choices System SummaryPower-on Password System InformationProduct Data System Card DataAdministrator Password Advanced SetupMemory Settings Start OptionsASM Settings Scalability Port ConfigurationScalable Partition Settings Error LogsConfiguring scalable partitions Creating a scalable partitionConfiguring the server Remote console redirection Deleting a scalable partitionPasswords Power-on passwordAdministrator password Using the ServerGuide Setup and Installation CD ServerGuide featuresSetup and configuration overview Typical operating-system installationInstalling your operating system without ServerGuide RSA II-EXAConfiguring the Gigabit Ethernet controller Using the LSI Logic Configuration Utility programUsing ServeRAID Manager Configuring the controller Configuration wizard windowUsing express configuration Click Express configurationUsing custom configuration Click Custom configurationConfiguration summary window Viewing the configuration ServeRAID Manager windowGetting assistance ServeRAID Manager help menuHints and tips feature Remote Supervisor Adapters Identifying the Remote Supervisor AdapterRemote Supervisor Adapter II-EXA features Setting up the Remote Supervisor Adapter II-EXASetup requirements Cabling and configuring the Remote Supervisor Adapter II-EXA StepASM Interconnect port USB connectorManagement ports Connect the RSA II-EXA breakout cable to the server Remote Supervisor Adapter II-EXA connectors Restrict to this brand field, select Servers Restrict to this brand field, select Servers Configuring and connecting to the ASM interconnect network XSeries 445 Type 8870 User’s Guide Configuring the server ASM interconnect network Ethernet configuration ASM interconnect network modem configuration Setting up the Remote Supervisor Adapter Remote Supervisor Adapter featuresCabling and configuring the Remote Supervisor Adapter PPP Remote Supervisor Adapter connectors Settings for Web-based remote Network Interface IP AddressSubnet Mask GatewayBaud Rate Dedicated to ASMStop Bits Line Type Authentication ProtocolRemote IP Address Configuring the server If the installation is from a diskette, type a\NT\SETUP -q Using the ASM interconnect network Select Save New Remote Control Password then, press EnterXSeries 445 Type 8870 User’s Guide Server name ASM Interconnect module needed Server name ASM Interconnect module needed Configuring the server ASM Interconnect network configuration Connecting modems to the ASM Interconnect network Starting the PXE boot agent utility program Using the PXE boot agent utility programPXE boot agent utility menu choices Using the documentation Before you callXSeries 445 Type 8870 User’s Guide Appendix B. Notices Edition noticeTrademarks IBMImportant notes Product recycling and disposalBattery return program Industry Canada Class a emission compliance statement European Union EMC Directive conformance statementTaiwanese Class a warning statement Avis de conformité à la réglementation d’Industrie CanadaXSeries 445 Type 8870 User’s Guide Macedonia former Yugoslav Republic of, Madagascar, Mali XSeries 445 Type 8870 User’s Guide Index LSI Starting server XSeries 445 Type 8870 User’s Guide Page Part Number 02R2784
Top Page Image Contents