IBM 8870 manual Settings for Web-based remote

Page 68

Note: For detailed information about using the ASM Web interface and the text-based user interface, see the Remote Supervisor Adapter User’s Guide on the IBM xSeries Documentation CD.

Table 3. Configuration tasks to enable remote access to the Remote Supervisor Adapter

User interface to Remote

Connection to Remote

For the configuration

Supervisor Adapter

Supervisor Adapter

procedure, see:

 

 

 

ASM Web interface using

LAN using the Ethernet port

“Configuring the Ethernet

HTTP

 

settings for Web-based remote

 

 

access”

Text-based user interface

 

 

 

using the Telnet protocol

 

 

 

 

 

Text-based user interface

Management (COM) port

“Configuring the management

using a modem or a null

 

port for text-based remote

modem

 

access” on page 58 and “Setting

 

 

up point-to-point protocol” on

ASM Web interface using

 

 

page 59

point-to-point protocol

 

 

 

(PPP)

 

 

 

 

 

Text-based user interface

 

 

using the Telnet protocol

 

 

over PPP

 

 

 

 

 

Configuring the Ethernet settings for Web-based remote access: If you have an accessible, active, and configured dynamic host configuration protocol (DHCP) server on the network, the hostname, IP address, gateway address, subnet mask, and DNS server IP address are set automatically. You do not need to perform further configuration tasks to enable the Ethernet connection because the default value for the DHCP Setting field is Enabled. If you need to configure the management port, go to “Configuring the management port for text-based remote access” on page 58; otherwise, go to “Installing Advanced System Management device drivers” on page 61.

If you do not have a DHCP server on the network, complete the following steps to configure the Ethernet settings.

1.With the server turned off, insert the diskette with the downloaded utility program into the diskette drive; then, turn on the server. The utility starts automatically, displaying the Remote Supervisor Utility window.

2.Use the arrow keys to select Configuration Settings; then, press Enter. The Configuration Settings window opens.

56xSeries 445 Type 8870: User’s Guide

Page 67 Page 69
Image 68
Page 67 Page 69
Contents ERserver Page ERserver Page Contents Iv xSeries 445 Type 8870 User’s Guide Safety To Connect To Disconnect Do not ≥ 18 kg 39.7 lb ≥ 32 kg 70.5 lb ≥ 55 kg 121.2 lb 82 kg 180 lb XSeries 445 Type 8870 User’s Guide Introducing the IBM xSeries 445 server Related documentationLearn section, click Online publications Click ContinueFeatures and specifications MicroprocessorWhat your server offers Light path diagnostics feature Redundant cooling and power capabilitiesLarge data-storage capacity and hot-swap capability Redundant connectionReliability, availability, and serviceability features UpdateXpress program Active MemoryMemory scrubbing and Memory ProteXion Memory mirroringIBM Director IBM Universal ManageabilityServer controls, LEDs, and power Front viewXSeries 445 Type 8870 User’s Guide Rear view Rear view of model with Remote Supervisor Adapter II-EXARemote Supervisor Adapter II-EXA connectors and LEDs Introducing the IBM xSeries 445 server Server power features Turning on the serverTurning off the server XSeries 445 Type 8870 User’s Guide Configuration/Setup Utility program Configuring scalable partitionsEthernet controller configuration Integrated System Management Processor Update programUsing the Configuration/Setup Utility program Starting the Configuration/Setup Utility programConfiguration/Setup Utility menu choices System SummaryPower-on Password System InformationProduct Data System Card DataAdministrator Password Advanced SetupMemory Settings Start OptionsASM Settings Scalability Port ConfigurationScalable Partition Settings Error LogsConfiguring scalable partitions Creating a scalable partitionConfiguring the server Remote console redirection Deleting a scalable partitionPasswords Power-on passwordAdministrator password Using the ServerGuide Setup and Installation CD ServerGuide featuresSetup and configuration overview Typical operating-system installationInstalling your operating system without ServerGuide RSA II-EXAConfiguring the Gigabit Ethernet controller Using the LSI Logic Configuration Utility programUsing ServeRAID Manager Configuring the controller Configuration wizard windowUsing express configuration Click Express configurationUsing custom configuration Click Custom configurationConfiguration summary window Viewing the configuration ServeRAID Manager windowGetting assistance ServeRAID Manager help menuHints and tips feature Remote Supervisor Adapters Identifying the Remote Supervisor AdapterSetup requirements Setting up the Remote Supervisor Adapter II-EXARemote Supervisor Adapter II-EXA features Cabling and configuring the Remote Supervisor Adapter II-EXA StepManagement ports USB connectorASM Interconnect port Connect the RSA II-EXA breakout cable to the server Remote Supervisor Adapter II-EXA connectors Restrict to this brand field, select Servers Restrict to this brand field, select Servers Configuring and connecting to the ASM interconnect network XSeries 445 Type 8870 User’s Guide Configuring the server ASM interconnect network Ethernet configuration ASM interconnect network modem configuration Setting up the Remote Supervisor Adapter Remote Supervisor Adapter featuresCabling and configuring the Remote Supervisor Adapter PPP Remote Supervisor Adapter connectors Settings for Web-based remote Network Interface IP AddressSubnet Mask GatewayBaud Rate Dedicated to ASMStop Bits Remote IP Address Authentication ProtocolLine Type Configuring the server If the installation is from a diskette, type a\NT\SETUP -q Using the ASM interconnect network Select Save New Remote Control Password then, press EnterXSeries 445 Type 8870 User’s Guide Server name ASM Interconnect module needed Server name ASM Interconnect module needed Configuring the server ASM Interconnect network configuration Connecting modems to the ASM Interconnect network PXE boot agent utility menu choices Using the PXE boot agent utility programStarting the PXE boot agent utility program Using the documentation Before you callXSeries 445 Type 8870 User’s Guide Appendix B. Notices Edition noticeTrademarks IBMImportant notes Product recycling and disposalBattery return program Industry Canada Class a emission compliance statement European Union EMC Directive conformance statementTaiwanese Class a warning statement Avis de conformité à la réglementation d’Industrie CanadaXSeries 445 Type 8870 User’s Guide Macedonia former Yugoslav Republic of, Madagascar, Mali XSeries 445 Type 8870 User’s Guide Index LSI Starting server XSeries 445 Type 8870 User’s Guide Page Part Number 02R2784
Top Page Image Contents