IBM 73P3309 manual Installation, Installing the drive, Opening the computer, Unpacking the drive

Page 19

Chapter 2. Installation

This chapter contains hardware and software installation instructions and operating information for the IBM Multi-Burner Plus.

Installing the drive

Complete the following steps to install the drive:

Step 1. Opening the computer

1.Turn off the computer and all attached devices.

2.Unplug all power cords from the computer and all attached devices.

3.Remove the cover from the computer. Refer to your computer documentation for instructions on removing the computer cover.

Step 2. Unpacking the drive

1.Before opening the antistatic bag that the drive is packed in, touch the bag to an unpainted metal surface for at least two seconds. This drains the static electricity from the package and your body.

2.Remove the drive from the bag.

If you must put the drive down, place the antistatic bag on a flat, padded surface, and place the drive on the antistatic bag.

Step 3. Setting the configuration jumpers

You can configure your drive as master , slave , or cable-select , by placing the jumper over the configuration pins as shown.

Use the following guidelines to determine the correct configuration for your drive.

vConfigure the drive as a master if it will be the only device that is connected to the IDE cable. This is the preset configuration.

vConfigure the drive as a slave if it will be the second device on an IDE cable. Be sure to configure the other device as a master. In some cases, a hard disk drive might require a “master with slave present” jumper setting when another device on the same cable is configured as a slave. For more information on setting configuration jumpers on other devices, refer to the documentation that comes with your computer.

vSome computers use special ATA cables with two wires reversed in the device connectors so that the drives can be configured by the cable instead of by jumper position. Use the cable-select position only for computers that are equipped with these special cables. See the documentation that comes with your computer to determine if your ATA adapter requires that you place the jumpers in the cable-select position.

© Copyright IBM Corp. 2004

2-1

Image 19

Contents IBM Multi- Burner Plus User’s Guide Page IBM Multi- Burner Plus User’s Guide Page Contents Appendix D. Service and Support Safety Read first Vi IBM Multi-Burner Plus User’s Guide Extension cords and related devices General safety guidelinesService Power cords and power adaptersHeat and product ventilation BatteriesCD and DVD drive safety IBM Multi-Burner Plus User’s Guide ″Introduction″ ″Installation″About this book Registering your productXii IBM Multi-Burner Plus User’s Guide Software description IBM Drive Letter Access DLAIntroduction Product descriptionHandling precautions Installation requirementsBefore you begin Drive controls and connectors 4IBM Multi-Burner Plus User’s Guide Opening the computer InstallationInstalling the drive Setting the configuration jumpersAttaching the cables to the drive Mounting the drive in the bayUsing the drive Completing the hardware installationInstalling the software Setting up the system for CD playbackRemoving the disc from the cartridge Using single and double-sided DVD-RAM mediaReturning the disc to the cartridge Using CD-R and CD-RW discsSecuring a disc in a vertically mounted drive Using the drive with CDs and DVDsManually ejecting a disc Using the DVD Player softwareBefore using the software Using the DVD PlayerClick the General Properties tab Using drive letter access DLAUsing the RecordNow software Click Intervideo WinDVDAbout CD and DVD images Making a bootable CD or DVDUsing Intervideo WinDVD Creator Plus RecordNow projectsHandling and caring for a disc Maintaining the driveCaring for the drive Installation 12IBM Multi-Burner Plus User’s Guide Environmental requirements Appendix A. Product specificationsPhysical specifications Power requirementsMedia Write speeds Write speedsSelect Control Panel Appendix B. Problem solving2IBM Multi-Burner Plus User’s Guide Disc cannot be read. Take the following actions You receive an error messageThere is no sound from the disc 4IBM Multi-Burner Plus User’s Guide Enabling DMA for Windows 2000 Professional Click Settings Click Control PanelClick the Advanced Settings tab Enabling DMA for Windows MeEnabling DMA for Windows XP Click Control Panel Click Switch to classic viewEnabling digital audio extraction Page 4IBM Multi-Burner Plus User’s Guide Online technical support Appendix D. Service and SupportTelephone technical support 2IBM Multi-Burner Plus User’s Guide What this Warranty Does not Cover What this Warranty CoversPart 1 General Terms Your Additional Responsibilities How to Obtain Warranty ServiceWhat IBM Will Do to Correct Problems Exchange of a Machine or PartGoverning Law Limitation of LiabilityJurisdiction Part 2 Country-unique TermsPeru CAMBODIA, LAOS, and Vietnam Malaysia Following Terms Apply to ALL Emea Countries Governing Law Following Terms Apply to ALL EU Countries 10IBM Multi-Burner Plus User’s Guide Egypt Items for Which IBM is Not Liable IrelandWarranty Period Part 3 Warranty InformationMulti-Burner Plus Customer Carry-In or Mail-In Service Types of Warranty ServiceCustomer Replaceable Unit ″CRU″ Service On-site ServiceCountry or Region Telephone Number 16IBM Multi-Burner Plus User’s Guide Trademarks Appendix F. NoticesAvis de conformite a la reglementation d’Industrie Canada Electronic emissions noticesFederal Communications Commission FCC statement Industry Canada Class B emission compliance statementUnion Européenne Directive Conformité électromagnétique European Union emission directiveUnione Europea Directiva EMC Conformidad électromagnética Union Europea Normativa EMC Page Part Number 73P3309