Cisco Systems MDS 9100 Series manual Removing and Installing Fan Modules

Page 58

Chapter 2 Installing the Cisco MDS 9100 Series

Removing and Installing Components

Step 4 Slide the power supply into the power supply bay. Make sure that the power supply is fully seated in the bay.

Step 5 Tighten the power supply captive screw.

Step 6 Plug the power cord into the power supply.

Step 7 Connect the other end of the power cord to an AC-input power source.

Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the Cisco MDS 9100 Series Switch to your outlet receptacle. See the “Jumper Power Cord” section on page C-5.

Step 8 Turn the power switch to the on () position on the power supply.

Step 9 Verify power supply operation by checking that the power supply (P/S) LED in the front panel is green.

If the LED is not green, see the Cisco MDS 9000 Family Troubleshooting Guide.

Removing and Installing Fan Modules

This section provides instructions for removing and installing the fan modules for the Cisco MDS 9140 Switch and the Cisco MDS 9120 Switch. The Cisco MDS 9124 Switch does not have field-replaceable fan modules.

Removing a Fan Module on the Cisco MDS 9140 Switch, the Cisco MDS 9120 Switch, and the Cisco MDS 9134 Switch

The fan module is designed to be removed and replaced while the system is operating without presenting an electrical hazard or damaging the system.

 

 

 

Caution

The Cisco MDS 9000 Family has internal temperature sensors that are capable of shutting down the

 

 

 

 

 

system if the temperature at different points within the chassis exceed certain safety thresholds. To be

 

 

 

 

 

effective, the temperature sensors require the presence of airflow; therefore, in the event a fan module is

 

 

 

 

 

removed from the chassis, the Cisco MDS 9000 Family will be shut down after five minutes to prevent

 

 

 

 

 

potentially undetectable overheating. However, the switches will shut down sooner if the higher-level

 

 

 

 

 

temperature threshold is exceeded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the

 

 

 

 

 

fan blades completely stop before you remove the fan tray. Statement 258

 

 

 

 

 

 

 

 

 

 

 

To remove the existing fan module, follow these steps:

 

 

 

 

 

 

 

 

Step 1

Locate the fan module in the back of the switch.

 

 

 

Step 2

Slide the seating tabs toward the center of the fan module.

 

 

 

Step 3

Grasp the fan module handle and pull it outward.

 

 

 

Cisco MDS 9100 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

2-30

 

 

 

OL-16187-01

 

 

 

 

 

 

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Cisco MDS 9100 Series Hardware Installation Guide Americas HeadquartersCisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Switch Port Cisco MDS 9124 Switch Specific Changed Feature Description Release Where DocumentedSwitch Installing the Cisco MDS Cisco MDS Description of the Cisco MDS 31aShelf Bracket Allows single-user installation Specific Installation ClearanceJumper power Jumper power cord available for Not release Kit Installation in a Telco rackOrganization AudienceChapter Title Description Document Conventions Chapter Title DescriptionPreface Related Documentation Regulatory Compliance and Safety InformationHardware Installation Release NotesInstallation and Configuration Note Command-Line InterfaceTroubleshooting and Reference Cisco MDS 9000 Family SSM Configuration NoteXiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 SwitchCisco MDS 9124 Switch Cisco MDS 9140 SwitchCisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Cisco MDS 9120 SwitchPower Supplies Fan ModulesCisco MDS 9100 Series Ports Ports on the Cisco MDS 9134 SwitchPorts Port Group 6shows the Cisco MDS 9134 ports Ports on the Cisco MDS 9124 Switch Cisco MDS 9124 PortsSwitch LEDs Fan module status LED10 Cisco MDS 9124 Switch LEDs LED Status DescriptionSupported SFP Transceivers Fibre Channel SFP TransceiversCombination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series Installation Options PreinstallationThis section includes the following information Installation Guidelines Unpacking and Inspecting the Switch Required EquipmentQuantity Installing the Switch in a Cabinet or RackTo 36-inch slider rails To 30-inch slider rails Per kitFront-Facing Installation Description Quantity96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Grounding the Switch LugStarting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Removing Power Supplies Removing and Installing Power SuppliesInstalling Power Supplies To remove the existing fan module, follow these steps Removing and Installing Fan ModulesLocate the fan module in the back of the switch Slide the seating tabs toward the center of the fan moduleOL-16187-01 Installing a Fan Module 25shows the Cisco MDS 9134 fan moduleVerifying the Fan Module OL-16187-01 Connecting the Console Port Preparing for Network ConnectionsConnecting the Console Port to a PC Connecting the Console CableConnecting the 10/100 Ethernet Management Port Connecting a Modem to a Console PortConnecting to a Fibre Channel Port Removing and Installing SFP TransceiversInstalling an SFP Transceiver SFP Transceiver with Mylar Tab LatchRemoving an SFP Transceiver Removing and Installing Cables into SFP Transceivers Installing a Cable into an SFP TransceiverConnecting the LC-Type Cable to a Fibre Channel Port Removing a Cable from an SFP TransceiverMaintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 General Requirements for Cabinets and Racks Cabinet and Rack RequirementsThis appendix includes the following information Requirements Specific to Perforated Cabinets Reference Perforated CabinetRequirements Specific to Standard Open Racks Cisco MDS 9000 Family Telco and EIA Shelf BracketRequirements Specific to Solid-Walled Cabinets Requirements Specific to Telco Racks45 lb 30 lb 15 lb Rack-Mounting GuidelinesRack Type MDS EIA 4-post Telco 2 postRequired Equipment Before Installing the Shelf BracketsInstalling the Shelf Bracket Kit into a Two-Post Telco Rack Quantity Part DescriptionCisco MDS 9100 Series Hardware Installation Guide Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 Installing the Shelf Bracket Kit into an EIA RackInstalling the Switch on the Shelf Brackets StatementRemoving the Shelf Bracket Kit Optional OL-16187-01 Switch Specifications Description SpecificationPower Specifications Power watts BTU/hr Amps General Power Supply SpecificationsAC-Input Power Supply Specification AC-Input Heat Diss 85 VAC 110 VAC 220 VACCisco Fibre Channel SFP Transceivers SFP Transceiver SpecificationsConnection Guidelines for AC-Powered Systems Part Number Description TypeConnector type Wavelength 850 nm 1310 nm Fiber type Description Short wavelength Long wavelengthCisco Gigabit Ethernet/Fibre Channel Transceivers General Specifications for Cisco GE/FC SFP TransceiversParameter Symbol Min Max Unit Gbps Ethernet SFPAdd/drop multiplexer for four Cwdm wavelengths Cisco Cwdm SFP TransceiversPart Number Description Add/drop multiplexer for eight Cwdm wavelengthsGeneral Specifications for Cisco Cwdm SFP Transceivers Description ColorParameter Symbol Minimum Typical Maximum Units Optical Specifications for Cisco Cwdm SFP TransceiversParameter Symbol Min Typical Max Units Modal Core Size Bandwidth Maximum Cabling X2 Product Number X2 Transceiver SpecificationsProduct Number Description Cable Type Microns MHz/km DistanceTransmit and Receive X2 Product Number ModalBandwidth Maximum Cabling X2 Product Number Wavelength nmOL-16187-01 Cable and Port Specifications Cables and AdaptersConsole Port Pin SignalConsole Port Pinouts RJ-45 to DB-25 Console Signal RJ-45 Pins DB-9 PinMgmt 10/100 Ethernet Port RJ-45 to DB-9 ConsolePower Cords Supported Power Cords and PlugsNot used Jumper Power Cord Figure C-3 300-W Power Supply PlugsC15 C14 Site Planning and Maintenance Records Site Preparation ChecklistTask No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4
Top Page Image Contents