Fujitsu Siemens Computers BS2000/OSD manual Displays in the case of a hardware error

Page 92

Problems with the S130

Troubleshooting

8.1.1 Displays in the case of a hardware error

The S130 informs you of hardware errors in the following manner:

●On the S130 control panel

If the yellow CHECK light illuminates, there may be a hardware error.

At the same time, the FLAG code appears on the LCD display. This can indicate an error in the service processor or a machine error.

●On the screen of the SKP console in the SVPST0 window

On the SKP console, displays in line 24 in the SVPST0 window of the SVP frame can indicate a hardware error. Evaluation of the FLAG code is carried out by the service department. The following diagram shows the format of the error display:

 

FLAG CODE = FFFFFFFF FFFFFFFF

LTG

TAST

Figure 44: FLAG code display in line 24 of the SVPST0 screen

The FLAG code FF . . . FF can have different meanings and can therefore require different measures:

–A WRITE-CONSOL message is displayed. It can be deleted with the F3 key. This does not delete the FLAG code display.

–A warning is issued, e.g. if the room temperature is too high. The cause of the error must be eradicated. System operation can continue in the meantime.

–An error has occurred in the S130 or on the interface to the peripheral devices which was automatically corrected by the hardware. In this case, system operation can also be continued.

–An error has occurred which does not permit system operation to be continued. In the last case, you can take the following measures:

If the system is down, execute an IMPL. If this does not solve the problem, contact the service department and discuss what steps should be taken.

92

U25339-J-Z126-1-7600

Page 91 Page 93
Image 92
Page 91 Page 93
Contents Introduction Objectives and target groupSummary of contents Notational conventionsSafety instructions S130 Business Server Global storage Battery unitImportant instructions Emergency StopManufacturer instructions Important instructions Manufacturer instructionsRFI suppression Overview Configuration levels of the S130 Business ServerS130-C Processing units S130-E S130-K S130-P S130-T Configuration levels of the S130 Business Server OverviewModel Number of processors Performance factor Concept of system operation HardwareConcept of system operation CPUConcept of system operation Overview Software Authorization control Controls and indicators Function of the indicators Control panel on the Business Server cabinet9999 StatusControls and indicators Control panel on the Business Server cabinetLine Displays in line Ffffffffffffffff Displays in line MeaningsCheck Power CompleteSystem Button functions Control panel on the global storage cabinet Control panel on the global storage cabinetCHK Cnct Ffffffffffffffff Line Displays in lineSSU Check Battery StatusThese indicators indicate the state of the backup battery Emergency Stop switch Emergency Stop switchUse the Emergency Stop switch as follows Emergency StopPage Switching the S130 Business Server on and off Switching the S130 on and off using the control panelSwitching on SKPSwitching off Switching the S130 on and off using the control panelAuxiliary Frame Load PRESET1 Switching the S130 on and off from the SKP Switching the S130 on and off from the SKPSwitching the S130 on and off from the SKP Switching the S130 on and off from the SKP Switching the S130 on and off from the SKP Switching the S130 on and off from the SKP Automatic switching on/off of the S130 via the SKP Automatic switching on/off of the S130 via the SKPAutomatic switching on/off of the S130 via the SKP Time-driven switching on and off of the SKP and S130 Time-driven switching on and off of the SKP and S130Switching the SKP and S130 on and off using Atop Switching the SKP and S130 on and off using AtopSwitching the S130 on and off from a remote system Switching global storage on and offSwitching the S130 on and off from a remote system DCUStandard processing in SVP mode Invoking an SVP frame Standard processing in SVP mode Invoking an SVP frameInvoking an SVP frame Password entry window is displayed SVPST0 #1 window password entryGeneral frame structure Standard processing in SVP modeGeneral frame structure System status messages in line HOST/GUESTCL-STOP General frame structure Standard processing in SVP mode Meaning of the status messages in lineDisplays of the emulated terminal 9750 and their meaning Hardware status display in lineStatus displays in line Using frames Using frames Standard processing in SVP modeSVP function keys P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 F1 F2 F3 P10Using frames Overview of the SVP function keysLock message Switching between user frames Explanation of figure Frames are represented by this symbolUser frames Standard processing in SVP mode User frames and subframesML Mode Selection Frame STOP/START Mode = Selection of a particular CPUUser frames LD Program Load Frame Basic Load Function =Preset Group Auxiliary Frame Load PRESET-1LD Program Load Frame DETAIL-1 Load ClearParms = MT Control = IPL from tapeIs not heeded, BS2000 will be shut down abruptly Cancel the procedureDETAIL-2 Status VM Mode = EXA Mode =LD Program Load Frame DETAIL-2 IPL Execution =P8 Switches to the SSU Frame see next ST Status Display Frame ClusterP7 Switches to the Cluster Frame see previous Status Display Frame SSU screenMA Manual Operation Frame Rate ControlAdrs Compare Stop Firmware DumpRate Control = Adrs Type =Unit Adrs = Adrs SET =Function = Adrs Comp Mode =AD ALTER/DISPLAY Frame Facility = ABSKEY Adrs =PSW FCRFPR PRXME Message Frame Message Frame screenCH CH/SUBCH Status Display Frame Channel CHP no =Chpid = 00 ... FFP10 P11 AU Auxiliary Frame Menu 8.1 AU1 Auxiliary Frame Real Clock Delete input Corrections are carried out by the SVPNext Power on Reset NO. = 8.2 AU2 Auxiliary Frame Iorsf ControlSET no ProtectSpecify Swap no Sets 4 to 7 are displayed Sets 0 to 3 are displayed8.3 AU3 Auxiliary Frame Related SCB’S Erase input Save input in SVPImpl Power OFF8.4 AU4 Auxiliary Frame P-OFF/IMPL Power on IPL = 8.5 AU5 Auxiliary Frame Load PRESET1Preset Group Load Frame Detail Initial Frame =Load Frame Basic Current 8.6 AU7 Auxiliary Frame SSU-CLUSTER ConfigurationStart IPL no = Init CFR File NO. = CFR File NO. =MF MSF Frame MSF Frame screenFrame line PA Performance Analyzer PA frame is not intended for useExamples of standard processing in SVP mode Enter the FR AU command in line 24 and press EnterSelecting Iorsf Selecting IorsfAuxiliary Frame Menu screen is displayed Enter 2 in the SELECTION= field. PressOn Reset NO.= field and press Enter Auxiliary Frame Iorsf Control screen is displayedSet Iorsf must be activated with a Impl Activating Iorsf Standard processing in SVP modeActivating Iorsf Setting up Program Load Frame PRESET1 Program Load Frame PRESET1Start Mode = IPL Device Preset GroupSetting up Program Load Frame PRESET2 Program Load Frame PRESET2You must be in the Auxiliary Frame Load PRESET2 screen Executing IPL in Program Load Frame DETAIL-1Load Function = IPL Device = Unit Address = MT Control =Frame Press the P9 key Program Load Frame DETAIL-2 screen appears Setting operating mode via Program Load Frame DETAIL-2You must be in the Program Load Frame DETAIL-1 screen Setting operating modeStandard processing in SVP mode System operation Operating the BS2000 consoleSelecting the console window Page Troubleshooting Problems with the S130Displays in the case of a hardware error Problems with the S130 TroubleshootingCarrying out a system dump TroubleshootingProblems with the S130 S130 with the high availability module Measures to take in the case of processing unit failureS130 without the high availability module Installation Y/N Following frame is displayedAre YOU Sure ? Enter Y or N N Problems with the service/console processor SKP Problems with the service/console processor SKPImportant key combinationsTroubleshooting Important key combinationsRelated publications Please apply to your local office for ordering the manualsSKP / 3970-KAx Operating Manual User GuideSinix Data Sheet Data Communication UnitBS2000/OSD-BC Introductory Guide to Systems Support User GuideIndex ALTER/DISPLAY Frame ADAtop CH/SUBCH Status Display Frame ChannelIndex IorsfMode Selection Frame Mode Selection Frame ML MSF Frame MF Manual Operation Frame MAMessage Frame ME Program Load Frame Basic LD DETAIL-1 DETAIL-2Starting Impl Status Display Frame ST ClusterSSU Structure of a frame Subframes SVP105 Page Contents Contents 101 109Page S130 Business Server Operating ManualEdition Jume 111

BS2000/OSD specifications

Fujitsu Siemens Computers BS2000/OSD represents a significant advancement in the realm of enterprise computing, particularly for trusted applications and mission-critical transactions. This mainframe-class operating system is tailored for large corporate environments, delivering reliability, performance, and security essential for contemporary data processing needs.

One of the most notable features of BS2000/OSD is its robust multitasking capabilities. Organizations can run multiple applications concurrently without sacrificing performance, allowing for efficient use of system resources. This is augmented by its advanced partitioning technology, which permits the segmentation of system resources into isolated environments. As a result, applications can be run in parallel, maximizing throughput and optimizing the overall performance of the system.

Security is paramount in any enterprise system, and BS2000/OSD excels in this area. The operating system offers comprehensive security features, including user authentication, access control, and sophisticated auditing tools. These capabilities ensure that sensitive data remains protected while providing users with the necessary permissions to perform their tasks.

BS2000/OSD is designed to support a wide range of technologies, making it highly versatile. Its compatibility with various programming languages, databases, and middleware allows organizations to adopt whatever tools best suit their needs. Furthermore, it integrates seamlessly with virtualization technologies, supporting both legacy applications and modern cloud-based services.

Another critical characteristic of BS2000/OSD is its emphasis on data integrity and fault tolerance. The system is equipped with features such as automatic error detection and correction functionalities. This significantly reduces downtime and enhances system availability—a fundamental requirement for businesses operating in high-stakes environments.

The operating system is also known for its sophisticated backup and recovery options. Data loss can be catastrophic, and BS2000/OSD mitigates this risk through automated backup processes and reliable disaster recovery protocols. This built-in resilience offers peace of mind to organizations that rely heavily on their data assets.

Fujitsu Siemens Computers has consistently focused on enhancing the performance and usability of BS2000/OSD. The user interface, while highly functional, is also intuitive, allowing users, including those not deeply familiar with mainframe systems, to navigate and operate it effectively.

In conclusion, Fujitsu Siemens Computers BS2000/OSD stands out as a powerful, reliable, and secure operating system for enterprise applications. With its multitasking capabilities, robust security features, compatibility with various technologies, and emphasis on data integrity, it remains an ideal choice for businesses seeking to enhance their operational efficiency in an increasingly digital world.
Top Page Image Contents